Cambridge IGCSE Physics 0625/63 (May/June 2026) — Complete Interactive Worked Solutions
Step-by-step worked solutions with clean exam apparatus diagrams, interactive tables, plotted graphs, official Cambridge mark codes, and 4-layer thinking scaffolding.
| Question | Core Practical Topic | Key ATP Skills Tested | Marks |
|---|---|---|---|
| Q1 | Density of identical coins (2 methods) | Significant figures, meniscus reading, full-size scale measurement, 10% accuracy test | 11 |
| Q2 | Spring extension vs. suspended mass | Extension arrow, parallax avoidance, graph plotting & best-fit line, $L = l_0 + e$, safety | 11 |
| Q3 | Resistors connected in parallel | Ammeter & voltmeter wiring, analogue scale ($0.05\text{ A}$/div), inverse proportionality, anomalies | 11 |
| Q4 | Rate of temperature rise of heated water | 7-mark experimental plan: variable, apparatus, method, controls, blank table, analysis | 7 |
Question 1 — Measuring the Density of Identical Coins
Total: 11 marksA student has five identical coins. The student measures the density of one of these coins by two different methods.
The student measures the mass $m_1$ of one coin. The reading on the balance is shown in Figure 1.1. Record the mass of the coin to two significant figures.
💡 Layer 1: Conceptual Orientation
Count significant figures starting from the first non-zero digit on the left. Look at the third digit on the display: should it round the tenths digit up or leave it unchanged?
🔍 Layer 2: Method & Analytical Guide
The raw display shows $8.89\text{ g}$ (3 significant figures). Because the third digit is $9 \ge 5$, round the second significant figure up from $8$ to $9$.
✅ Layer 3: Full Worked Solution & Mark Scheme
Balance reading $= 8.89\text{ g}$. Rounding to 2 significant figures:
Examiner Trap: Writing $8.89\text{ g}$ or $8.8\text{ g}$ scores 0/1. Whenever Cambridge bolds a rounding command, the mark is awarded strictly for correct rounding.
The student slowly lowers the five coins into a measuring cylinder until they are completely covered with water. Figure 1.2 shows the initial volume of water; Figure 1.3 shows the final reading after the coins have been lowered in. Record the initial and final readings.
💡 Layer 1: Conceptual Orientation
Determine the least count first: numbered graduations increase by $2\text{ cm}^3$ with one unlabelled tick halfway between each pair. What volume does each small tick represent?
🔍 Layer 2: Method & Analytical Guide
Each small division $= 1\text{ cm}^3$. Read the bottom of the meniscus: in Figure 1.2 it sits halfway between $10$ and $12$; in Figure 1.3 it sits halfway between $16$ and $18$.
✅ Layer 3: Full Worked Solution & Mark Scheme
Final reading $= \mathbf{17}\text{ cm}^3$ [B1 for both]
Why submerge five coins slowly? Measuring five coins together reduces percentage uncertainty in volume by a factor of $5$. Lowering them slowly prevents water splashing out and avoids trapping air bubbles under the coins.
Calculate the volume $V_1$ of one coin using your values from 1(a)(ii) and the equation:
💡 Layer 1: Conceptual Orientation
The water-level rise equals the total volume of all five coins. Dividing by $5$ yields the average volume of one coin.
🔍 Layer 2: Method & Analytical Guide
Total displaced volume $= 17 - 11 = 6\text{ cm}^3$. Divide $6\text{ cm}^3$ by $5$.
✅ Layer 3: Full Worked Solution & Mark Scheme
Error Carried Forward (ECF): Always write out your substitution step so examiners can award ECF credit even if a previous reading was slightly off.
Describe one technique for measuring the volume of water in the measuring cylinder to ensure an accurate reading.
Which statement earns the mark in a Cambridge Paper 6 mark scheme?
💡 Layer 1: Conceptual Orientation
Think about how eye position affects apparent scale alignment (parallax error) and which part of the curved water surface is calibrated on glass measuring cylinders.
🔍 Layer 2: Method & Analytical Guide
Keep your line of sight perpendicular to the scale at eye level, read from the bottom of the concave meniscus, and rest the cylinder on a flat horizontal bench.
✅ Layer 3: Full Worked Solution & Mark Scheme
Any one of the following earns full credit:
- View the scale perpendicularly / at eye level to avoid parallax error. [B1]
- Read from the bottom of the meniscus. [B1]
- Place the measuring cylinder on a flat, horizontal surface. [B1]
Examiner Trap: Writing only "avoid parallax error" without stating how ("view perpendicularly / at eye level") often loses the mark. Always state the physical action.
Calculate the density $\rho_1$ of one coin using your values from 1(a)(i) and 1(a)(iii) and the equation $\rho_1 = \dfrac{m_1}{V_1}$. Include the unit.
💡 Layer 1: Conceptual Orientation
Your mass is in $\text{g}$ and volume is in $\text{cm}^3$, so dividing directly gives density in $\text{g/cm}^3$ without any unit conversion needed.
🔍 Layer 2: Method & Analytical Guide
Substitute $m_1 = 8.9\text{ g}$ and $V_1 = 1.2\text{ cm}^3$ into $\rho_1 = m_1 / V_1$ and round to 2 or 3 significant figures.
✅ Layer 3: Full Worked Solution & Mark Scheme
Sanity Check: Coin alloys (steel, brass, cupronickel) have densities around $7.0\text{–}8.9\text{ g/cm}^3$, confirming that $7.4\text{ g/cm}^3$ is physically realistic.
The student makes a stack of the five coins, drawn full size in Figure 1.4, and records the mass $m_5 = 43.6\text{ g}$. Measure the height $h_5$ of the five coins in Figure 1.4.
💡 Layer 1: Conceptual Orientation
Trace horizontally from the top edge of the fifth coin across to the millimetre ruler on the right. How many millimetres above $1.0\text{ cm}$ does it align with?
🔍 Layer 2: Method & Analytical Guide
On the true-to-scale A4 PDF, each coin measures $0.28\text{ cm}$ thick, so five coins stacked flush measure $5 \times 0.28\text{ cm} = 1.40\text{ cm}$.
✅ Layer 3: Full Worked Solution & Mark Scheme
Printing Tip: Always print past papers at 100% Actual Size so full-size diagrams are not shrunk by "Fit to Page".
The radius $r$ of each coin is $1.2\text{ cm}$. Calculate the volume $V_5$ of the five coins using your value from 1(b)(i) and the equation:
💡 Layer 1: Conceptual Orientation
The stack is modelled as a cylinder of radius $r = 1.2\text{ cm}$ and height $h_5 = 1.4\text{ cm}$. Remember to square only $r$.
🔍 Layer 2: Method & Analytical Guide
Compute $r^2 = (1.2)^2 = 1.44\text{ cm}^2$, then multiply by $\pi$ and by $1.4\text{ cm}$.
✅ Layer 3: Full Worked Solution & Mark Scheme
Keep the full unrounded calculator display ($6.333\dots$) in memory for part 1(b)(iii) to avoid rounding drift.
Calculate another value $\rho_2$ for the density of one coin using the values from 1(b) ($m_5 = 43.6\text{ g}$) and the equation $\rho_2 = \dfrac{m_5}{V_5}$.
💡 Layer 1: Conceptual Orientation
Both $m_5$ and $V_5$ belong to the same five identical coins, so dividing them directly gives the density of the coin material without dividing by $5$ again.
🔍 Layer 2: Method & Analytical Guide
Substitute $m_5 = 43.6\text{ g}$ and $V_5 = 6.333\text{ cm}^3$ into $\rho_2 = m_5 / V_5$.
✅ Layer 3: Full Worked Solution & Mark Scheme
Examiner Trap: Never divide $\rho_2$ by $5$ at the end. Density is an intensive property: one coin and five identical coins have the exact same density.
Two quantities can be considered equal within the limits of experimental accuracy if their values are within $10\%$ of each other. State whether $\rho_1$ from Method 1 and $\rho_2$ from Method 2 can be considered equal. Support your statement with a calculation.
Compare $\rho_1 = 7.4\text{ g/cm}^3$ and $\rho_2 = 6.9\text{ g/cm}^3$:
💡 Layer 1: Conceptual Orientation
Do not judge by eye. Compute the percentage difference between $\rho_1$ and $\rho_2$, then compare your result directly against the $10\%$ limit.
🔍 Layer 2: Method & Analytical Guide
Step 1: Find the difference $|\rho_1 - \rho_2| = 7.4 - 6.9 = 0.5\text{ g/cm}^3$.
Step 2: Divide by $\rho_1$ (or $\rho_2$) and multiply by $100\%$ to get the percentage difference.
✅ Layer 3: Full Worked Solution & Mark Scheme
Note: Dividing by $6.9$ instead gives $7.2\%$, which is also less than $10\%$.
Statement: Yes, $\rho_1$ and $\rho_2$ can be considered equal within the limits of experimental accuracy because their percentage difference is less than $10\%$. [A1]
Why is $\rho_2$ slightly lower than $\rho_1$? Embossed coin surfaces trap tiny air gaps between stacked coins, slightly overestimating $h_5$ and $V_5$ and pulling $\rho_2$ slightly below $\rho_1$.
Question 2 — Hooke's Law: Spring Extension & Graphical Analysis
Total: 11 marksA student investigates the relationship between the extension $e$ of a spring and the mass $m$ suspended from the spring using masses of $10\text{ g}, 20\text{ g}, 30\text{ g}, 40\text{ g},$ and $50\text{ g}$.
Figure 2.1 shows the arrangement of the apparatus. On Figure 2.1, draw a double-headed arrow (↕) to show the extension of the spring when mass $m$ is suspended from the spring.
Where must the double-headed arrow for extension $e$ start and end?
💡 Layer 1: Conceptual Orientation
Extension is the increase in length, $e = L - l_0$. Since both springs start at the same clamp height, compare the positions of their lower ends.
🔍 Layer 2: Method & Analytical Guide
Project a horizontal dashed line from the bottom end of $l_0$ across to the stretched spring. Draw a vertical double-headed arrow between that level and the bottom end of $L$.
✅ Layer 3: Full Worked Solution & Mark Scheme
Examiner Trap: Match the exact endpoints used by the exam paper's own $l_0$ and $L$ arrows (the ends of the coiled section); do not extend your arrow down to the mass hanger.
Describe two techniques the student uses to measure accurately the length of the spring.
Which pair of techniques earns full 2/2 marks?
💡 Layer 1: Conceptual Orientation
Consider how to prevent parallax error, ruler tilt, and oscillation errors when measuring a vertically suspended spring.
🔍 Layer 2: Method & Analytical Guide
State two concrete physical methods: eye-level perpendicular reading, a set square or horizontal pointer, clamping the ruler vertically close to the spring, or waiting for oscillations to stop.
✅ Layer 3: Full Worked Solution & Mark Scheme
Any two distinct techniques [B1] + [B1]:
- View the ruler scale perpendicularly / at eye level to avoid parallax error.
- Use a set square or horizontal pointer against the ruler to align the ends of the spring with the scale.
- Clamp the ruler vertically and place it as close as possible to the spring.
- Wait until the spring and mass have stopped oscillating before reading.
Examiner Trap: Vague statements such as "measure carefully" or "avoid human error" receive 0 marks.
Calculate the extension $e$ when a mass of $40\text{ g}$ is suspended from the spring using $e = L - l_0$, and enter your value in Table 2.1.
| mass $m$ / g | length $L$ / cm | extension $e$ / cm |
|---|---|---|
| 0 | 1.9 | 0.0 |
| 10 | 2.4 | 0.5 |
| 20 | 2.8 | 0.9 |
| 30 | 3.3 | 1.4 |
| 40 | 3.7 | |
| 50 | 4.2 | 2.3 |
💡 Layer 1: Conceptual Orientation
Read the original unstretched length $l_0$ from the $m = 0\text{ g}$ row of Table 2.1, then subtract it from $L$ at $m = 40\text{ g}$.
🔍 Layer 2: Method & Analytical Guide
From row 1, $l_0 = 1.9\text{ cm}$. At $m = 40\text{ g}$, $L = 3.7\text{ cm}$. Compute $3.7 - 1.9$.
✅ Layer 3: Full Worked Solution & Mark Scheme
Checking successive differences ($0.0 \to 0.5 \to 0.9 \to 1.4 \to 1.8 \to 2.3$) confirms a steady rise of $0.4\text{–}0.5\text{ cm}$ per $10\text{ g}$.
Plot a graph of extension $e/\text{cm}$ ($y$-axis) against mass $m/\text{g}$ ($x$-axis). Start the axes from the origin $(0,0)$ and draw a best-fit straight line.
Which plotting method earns all 3 Cambridge graph marks?
💡 Layer 1: Conceptual Orientation
Cambridge graph marks reward three distinct habits: sensible linear scales covering at least half of each axis, accurate plotting to within half a small square, and a single thin best-fit line.
🔍 Layer 2: Method & Analytical Guide
- $x$-axis scale: $0$ to $50\text{ g}$ using $10\text{ g}$ per major square ($1\text{ small div} = 2\text{ g}$).
- $y$-axis scale: $0$ to $2.5\text{ cm}$ using $0.5\text{ cm}$ per major square ($1\text{ small div} = 0.1\text{ cm}$).
- Points to plot: $(0,0.0), (10,0.5), (20,0.9), (30,1.4), (40,1.8), (50,2.3)$.
✅ Layer 3: Full Plotted Graph & Mark Scheme
- Suitable linear scales from $(0,0)$ filling ≥50% of both axes [B1]
- All 6 points plotted accurately to within $\pm \frac{1}{2}$ small square [B1]
- Thin, well-balanced straight line of best fit drawn with a ruler [B1]
Use a sharp HB pencil and small neat crosses (×). Thick blobs or double-drawn lines immediately lose the best-fit line mark.
Use your graph to determine the length $L$ of the spring when a mass of $12\text{ g}$ is suspended from the spring. Show clearly on the graph how you obtained the necessary information.
💡 Layer 1: Conceptual Orientation
The $y$-axis of your graph reads extension $e$, but the question asks for total length $L$. What must you add to $e$ after reading the graph?
🔍 Layer 2: Method & Analytical Guide
Step 1: Draw a vertical dashed line from $m = 12\text{ g}$ up to the best-fit line, then horizontally to the $y$-axis to read $e \approx 0.55\text{ cm}$.
Step 2: Add the original unstretched length $l_0 = 1.9\text{ cm}$ using $L = l_0 + e$.
✅ Layer 3: Full Worked Solution & Mark Scheme
Extension read from best-fit line: $e = 0.55\text{ cm}$ (accept $0.5\text{–}0.6\text{ cm}$) [B1]
$L = \mathbf{2.45}\text{ cm}$ (or $\mathbf{2.5}\text{ cm}$) [B1]
Classic 3-Mark Trap: Writing $L = 0.55\text{ cm}$ stops one step too early. Always check whether the answer line asks for extension $e$ or total length $L$.
Suggest one safety precaution the student takes when doing the experiment.
Select the specific safety precaution for a spring-and-masses experiment:
💡 Layer 1: Conceptual Orientation
Focus on the two real physical hazards: a stretched spring snapping toward your eyes, or slotted masses dropping onto your feet.
🔍 Layer 2: Method & Analytical Guide
State one concrete protective action: safety goggles, a cushioned mat under the masses, or clamping the retort stand to the bench.
✅ Layer 3: Full Worked Solution & Mark Scheme
Any one valid precaution [B1]:
- Wear safety goggles / eye protection in case the spring snaps.
- Place a cushion / soft mat underneath the masses (or keep feet out of the way).
- Clamp the retort stand securely to the bench with a G-clamp or counterweight.
Generic lab rules ("tie hair back", "do not run") never earn credit in Paper 6; link your precaution directly to the apparatus.
Question 3 — Electric Circuit with Combinations of Parallel Resistors
Total: 11 marksA student investigates an electric circuit containing different combinations of identical resistors connected in parallel.
On Figure 3.1, complete the circuit to show a voltmeter connected to measure the potential difference (p.d.) across the resistor, and an ammeter connected to measure the current in the circuit.
How should the ammeter and voltmeter be connected?
💡 Layer 1: Conceptual Orientation
Current flows through an ammeter (connected in series), whereas potential difference is measured across a component by a voltmeter (connected in parallel).
🔍 Layer 2: Method & Analytical Guide
Draw a circle with A closing the right-hand gap. Add a parallel branch across the resistor containing a circle with V.
✅ Layer 3: Full Worked Solution, Completed Circuit & Mark Scheme
Ammeter symbol (A) connected in series in the right-hand gap [B1]
Never draw a connecting wire straight through the meter circle, and ensure all junctions meet cleanly without breaks.
The student measures the p.d. $V$ across the resistor and the current $I$ in the circuit. Record, in Table 3.1, the value of $I$ shown on the ammeter in Figure 3.2.
💡 Layer 1: Conceptual Orientation
Count the number of small intervals between $0$ and $0.5\text{ A}$ to find the value of one small division before reading the pointer.
🔍 Layer 2: Method & Analytical Guide
There are $10$ small divisions between $0$ and $0.5\text{ A}$, so each small division $= 0.05\text{ A}$. The pointer sits on the 6th tick after $0$.
✅ Layer 3: Full Worked Solution & Mark Scheme
Recording $0.30$ matches the 2-decimal-place precision of the other readings in Table 3.1 ($0.60, 0.85, 1.15, 1.45$).
(i) Complete the column headings in Table 3.1. (ii) Calculate the resistance $R$ when there is one resistor in the circuit using $R = \dfrac{V}{I}$.
| number of resistors | $V$ / | $I$ / | $R$ / |
|---|---|---|---|
| 1 | 0.75 | 0.30 | |
| 2 | 0.75 | 0.60 | 1.25 |
| 3 | 0.75 | 0.85 | 0.88 |
| 4 | 0.75 | 1.15 | 0.65 |
| 5 | 0.75 | 1.45 | 0.52 |
💡 Layer 1: Conceptual Orientation
Recall the SI unit symbols for potential difference, current, and resistance, then compute $R = V/I$ for row 1.
🔍 Layer 2: Method & Analytical Guide
Complete the headings as $V / \text{V}$, $I / \text{A}$, and $R / \Omega$ (you can type ohm or Ω), then divide $0.75$ by $0.30$.
✅ Layer 3: Full Worked Solution & Mark Scheme
3(c)(ii) Resistance for 1 resistor: $R = \mathbf{2.50}\ \Omega$ (or $2.5\ \Omega$) [B1]
Recording $2.50$ keeps every entry in the $R$ column consistent to 2 decimal places.
Describe the relationship between the number of resistors in the circuit and the resistance $R$ in the circuit. Justify your answer using values from Table 3.1.
Which response earns both marks?
💡 Layer 1: Conceptual Orientation
For $N$ identical resistors in parallel, $R = R_1 / N$. To prove inverse proportionality from Table 3.1, test whether the product $N \times R$ remains approximately constant.
🔍 Layer 2: Method & Analytical Guide
| $N$ | 1 | 2 | 3 | 4 | 5 |
|---|---|---|---|---|---|
| $R$ / $\Omega$ | 2.50 | 1.25 | 0.88 | 0.65 | 0.52 |
| $N \times R$ / $\Omega$ | 2.50 | 2.50 | 2.64 | 2.60 | 2.60 |
When $N$ doubles from $1$ to $2$, $R$ halves from $2.50\ \Omega$ to $1.25\ \Omega$, and $N \times R$ stays close to $2.55\ \Omega$ across all five rows.
✅ Layer 3: Full Worked Solution & Mark Scheme
Justification: Doubling $N$ from $1$ to $2$ halves $R$ from $2.50\ \Omega$ to $1.25\ \Omega$, and the product $N \times R$ stays constant at $2.5\text{–}2.6\ \Omega$ within experimental accuracy. [B1]
Notice that $N \times R$ rises slightly from $2.50$ to $2.64$ as total current increases — a direct clue to the heating effect discussed in 3(c)(iv).
The resistors heat up during the investigation and this affects the values for the resistance $R$. Suggest two improvements to reduce this heating effect.
Which pair of improvements directly reduces electrical heating?
💡 Layer 1: Conceptual Orientation
Heating energy is $E = I^2Rt = (V^2/R)t$. Reduce either the time $t$ current flows, the supply voltage $V$, or the current $I$.
🔍 Layer 2: Method & Analytical Guide
Pair one procedural improvement (switching off between readings) with one circuit improvement (lower supply e.m.f., series protective resistor, or higher-value resistors).
✅ Layer 3: Full Worked Solution & Mark Scheme
Any two distinct improvements [B1] + [B1]:
- Switch off / open the switch between readings so current flows only briefly.
- Use a lower supply voltage to reduce current.
- Add a fixed or variable resistor in series with the power supply to limit current.
- Use resistors of higher resistance.
Always state how to reduce current (e.g., lower supply voltage or add a series resistor) rather than writing "use a smaller current" alone.
The student takes repeat readings. Table 3.2 shows the ammeter readings for three resistors in parallel: 0.85, 0.58, 0.90, 0.80. Identify the anomalous reading and suggest one reason for this anomaly.
💡 Layer 1: Conceptual Orientation
Three readings cluster tightly around $0.80\text{–}0.90\text{ A}$. Which value sits far outside that group, and what circuit fault or reading mistake could produce it?
🔍 Layer 2: Method & Analytical Guide
$0.58\text{ A}$ is almost identical to the 2-resistor current ($0.60\text{ A}$) in Table 3.1, pointing to a loose connection on one resistor, or digit transposition ($0.85 \to 0.58$).
✅ Layer 3: Full Worked Solution & Mark Scheme
Reason (any one): One resistor had a loose/poor connection; or the student misread the ammeter scale / transposed the digits; or the resistors overheated. [B1]
When calculating a mean from repeat readings, always exclude the anomaly: $(0.85 + 0.90 + 0.80) / 3 = 0.85\text{ A}$.
Question 4 — Experimental Planning: Rate of Heating Water
Total: 7 marksA student investigates the rate at which the temperature of water inside a beaker increases when the water is heated. Plan an experiment to investigate how one variable affects the rate at which the temperature of the water increases.
Apparatus available: a selection of beakers, an electrical water heater, and a supply of water. In your plan: state the one variable investigated; name any other apparatus needed; describe the method and measurements; state key control variables; draw a table with column headings (no readings entered); and explain how to use the readings to reach a conclusion.
If you choose volume of water as your independent variable, which apparatus and control set is complete for full marks?
💡 Layer 1: Conceptual Orientation
Rate of temperature increase is $\dfrac{\theta_2 - \theta_1}{t}$, so you must measure both temperature change and time, and repeat across at least 5 values of your chosen independent variable.
🔍 Layer 2: Method & Analytical Guide
Vary the volume of water across 5 values ($100, 150, 200, 250, 300\text{ cm}^3$), keep the beaker, heater power, starting temperature, and heating time ($180\text{ s}$) constant, and plot rate of temperature rise against volume.
✅ Layer 3: Full 7-Mark Model Plan & Mark Scheme
1. Independent variable: Volume (or mass) of water in the beaker. [B1]
2. Additional apparatus: Thermometer, stopwatch / stopclock, measuring cylinder (or top-pan balance), and stirrer. [B1]
3. Method & measurements: [B2]
- Measure $100\text{ cm}^3$ of water with the measuring cylinder and pour it into a beaker.
- Record the initial temperature $\theta_1$ with the thermometer (bulb clear of the beaker base).
- Immerse the electrical heater fully, switch it on, and start the stopwatch simultaneously.
- After a fixed time $t = 180\text{ s}$, stir the water gently and record the final temperature $\theta_2$.
- Repeat for at least four other volumes ($150, 200, 250, 300\text{ cm}^3$), letting the heater cool between trials.
4. Key control variables: Same heater and power supply voltage; same initial temperature $\theta_1$; same beaker (material & diameter) and room temperature; same heating time $t$. [B1]
5. Results table (headings with units, no data): [B1]
| Volume $V$ / cm³ | Initial temp. $\theta_1$ / °C | Final temp. $\theta_2$ / °C | Temp. rise $\Delta\theta$ / °C | Time $t$ / s | Rate / °C s−1 |
|---|---|---|---|---|---|
6. Reaching a conclusion: Calculate $\text{rate} = \dfrac{\theta_2 - \theta_1}{t}$ for each volume and plot a graph of rate ($y$-axis) against volume of water ($x$-axis) to see how volume affects the heating rate. [B1]
You can equally earn 7/7 by investigating the diameter / surface area of the beaker (extra apparatus: ruler, thermometer, stopwatch, measuring cylinder) or beaker material / insulation (keeping water volume constant).
Final Revision Checklist — Top 6 Cambridge Paper 6 Habits
- Bold Rounding Commands: Always honour bolded instructions such as two significant figures (Q1(a)(i)) and match existing table decimal places (Q3(b), Q3(c)(ii)).
- Least Count First: Divide the gap between two numbered marks by the number of small divisions before reading any scale (Q1(a)(ii): $1\text{ cm}^3$; Q3(b): $0.05\text{ A}$).
- Extension vs. Total Length: Re-read the symbol on the answer line ($e$ vs. $L$) after reading off a Hooke's law graph (Q2(b)(iii)).
- Numerical 10% Justification: Always show a percentage difference calculation before stating two results are equal within experimental limits (Q1(c)).
- Inverse Proportionality Proof: Check $N \times R \approx \text{constant}$ or a doubling/halving pair from the table (Q3(c)(iii)).
- 7-Mark Plan Structure: Address all 6 prompt bullets with bold headings, at least 5 trials, and units in every table header (Q4).