Thursday, 5 November 2026

Cambridge O Level Physics 5054/31 Oct/Nov 2025 Paper 3 Practical Worked Solutions & Sample Data

CAMBRIDGE O LEVEL PHYSICS (5054) PAPER 31 PRACTICAL TEST OCT/NOV 2025 (W25)

Cambridge O Level Physics 5054/31 Oct/Nov 2025: Interactive Practical Worked Solutions & Sample Data

Complete hands-on experimental guide, realistic supervisor sample readings from Confidential Instructions, interactive self-check inputs, and 4-layer analytical scaffolding with official Mark Scheme breakdown. Total Marks: 40 | Time Allowed: 1 hour 30 minutes.

Question 1: Thermal Efficiency of an Electric Heater Coil

10 Marks

Experimental Context & Supervisor Setup: In this experiment, you measure the thermal efficiency of a small electric heater constructed from a $50\text{ cm}$ coil of $28\text{ swg}$ constantan wire (approximate resistance $2\text{ }\Omega$) immersed at the bottom of a $100\text{ cm}^3$ heat-resistant glass beaker. A d.c. power supply, an ammeter, a voltmeter, and an open switch are pre-connected as shown in Fig. 1.1.

Fig. 1.1: Bench Apparatus Arrangement d.c. power supply A V 50 cm³ water coil of wire 100 cm³ beaker Part (a): Standard Schematic Circuit Diagram d.c. supply switch A Heater (R) V ✓ Series loop: Supply + Ammeter + Switch + Heater ✓ Parallel branch: Voltmeter across Heater
1(a)

In the answer space, draw a circuit diagram of the circuit that has been set up for you. [2 marks]

Select the correct circuit configuration rules required by the Cambridge Mark Scheme:

💡 Layer 1: Conceptual Orientation

Look at Fig. 1.1 on the left side of the diagram above. How do we represent the physical coil of constantan wire using standard IEC/Cambridge circuit symbols? Which meter lies in the main loop carrying the current $I$, and which meter bridges across the two crocodile clips?

🔍 Layer 2: Method & Analytical Guide
  • Replace the physical coil in the beaker with a standard rectangular fixed resistor symbol (heating element).
  • Trace the main series loop: d.c. power supply (two open circles or cell/battery symbol) $\rightarrow$ ammeter ($\text{A}$) $\rightarrow$ heater resistor $\rightarrow$ open switch.
  • Connect the voltmeter ($\text{V}$) in a parallel branch across the heater (or across the power supply terminals when the switch is closed).
✅ Layer 3: Full Worked Solution & Mark Scheme

Refer to the right-hand panel of the SVG diagram above for the full-mark schematic drawing:

  • Power supply/battery, heater (resistor symbol), ammeter, and (closed or open) switch connected in a single series loop. [B1]
  • Voltmeter connected in parallel across the heater (or across the power supply). [B1]
🚀 Layer 4: Examiner's Extension Challenge: Never draw a literal curly "spring" or picture of a beaker inside a formal circuit schematic! Always use the standard rectangle symbol for a resistor/heater, and ensure circuit corners meet cleanly without gaps.
1(b) & 1(c)(i)–(ii)

(b) Measure $50\text{ cm}^3$ of water into the beaker covering the heater. Record the initial water temperature $\theta_0$. [1 mark]
(c)(i) Close the switch and start the stopwatch. Record the current $I$ and potential difference $V$ across the heater. [1 mark]
(c)(ii) Leave switched on for $5\text{ minutes}$ ($300\text{ s}$) while stirring gently. Open the switch, stir for a further minute, and record the final temperature $\theta_F$. Calculate $\Delta\theta = \theta_F - \theta_0$. [1 mark]

📋 Standard Supervisor Sample Experimental Readings (Per Confidential Instructions)
Water Volume ($V_w$): $50\text{ cm}^3$
Initial Temp ($\theta_0$): $24.0\text{ }^\circ\text{C}$
Current ($I$): $1.40\text{ A}$ (Allowed: $1.30\text{ A} \pm 0.50\text{ A}$)
Voltage ($V$): $2.9\text{ V}$ (Allowed: $3.0\text{ V} \pm 0.5\text{ V}$)
Heating Time ($t$): $300\text{ s}$ ($5.0\text{ min}$)
Final Temp ($\theta_F$): $28.5\text{ }^\circ\text{C}$
°C
💡 Layer 1: Conceptual Orientation

What precision is required by the mark scheme when recording ammeter and voltmeter readings in a practical exam? How is the temperature rise $\Delta\theta$ defined from your initial and final thermometer readings?

🔍 Layer 2: Method & Analytical Guide
  • Precision check: Current $I$ must be recorded to $0.01\text{ A}$ or better (e.g., $1.40\text{ A}$) and voltage $V$ to $0.1\text{ V}$ or better (e.g., $2.9\text{ V}$).
  • Temperature change formula: Substitute $\theta_0 = 24.0\text{ }^\circ\text{C}$ and $\theta_F = 28.5\text{ }^\circ\text{C}$ into $\Delta\theta = \theta_F - \theta_0$.
✅ Layer 3: Full Worked Solution & Mark Scheme
  • 1(b): $\theta_0 = 24.0\text{ }^\circ\text{C}$ (any sensible room temperature between $15\text{ }^\circ\text{C}$ and $32\text{ }^\circ\text{C}$ recorded). [B1]
  • 1(c)(i): $I = 1.40\text{ A}$ (within $1.30\text{ A} \pm 0.50\text{ A}$, recorded to $0.01\text{ A}$ or better) AND $V = 2.9\text{ V}$ (within $3.0\text{ V} \pm 0.5\text{ V}$, recorded to $0.1\text{ V}$ or better). [B1]
  • 1(c)(ii): $\theta_F = 28.5\text{ }^\circ\text{C}$ (must satisfy $\theta_F \ge \theta_0$) and temperature change: $$\Delta\theta = \theta_F - \theta_0 = 28.5 - 24.0 = 4.5\text{ }^\circ\text{C}$$ [B1]
1(c)(iii)

Explain why the water is stirred for a further minute after the circuit is switched off. [1 mark]

💡 Layer 1: Conceptual Orientation

Immediately after the current stops, the constantan coil at the bottom of the beaker is still hotter than the surrounding water, and warm water rises by convection. What happens if you read the thermometer immediately without stirring?

🔍 Layer 2: Method & Analytical Guide

Consider thermal equilibrium and heat distribution: stirring mixes warmer and cooler regions of water and allows thermal transfer from the hot wire to complete.

✅ Layer 3: Full Worked Solution & Mark Scheme

Official Answer: To ensure that the water is at a uniform temperature throughout the beaker / to ensure that all the thermal energy (heat) from the coil is absorbed by the water before taking the final reading. [B1]

1(d)(i)–(iii)

(i) Calculate the electrical energy $Q_H$ supplied by the heater using $Q_H = I \times V \times t$, where $t = 300\text{ s}$. [1 mark]
(ii) Calculate the thermal energy $Q_W$ gained by the water using $Q_W = 50 \times 4.2 \times \Delta\theta$. [1 mark]
(iii) Calculate the efficiency of the heater using $\text{efficiency} = \dfrac{Q_W}{Q_H}$. [1 mark]

Using our sample values ($I = 1.40\text{ A}$, $V = 2.9\text{ V}$, $t = 300\text{ s}$, $\Delta\theta = 4.5\text{ }^\circ\text{C}$), enter your calculated results:

J
J
💡 Layer 1: Conceptual Orientation

Why must $Q_W$ always be less than or equal to $Q_H$ in a real laboratory experiment? Check the conservation of energy: where does the "missing" energy go during the $5\text{ minutes}$ of heating?

🔍 Layer 2: Method & Analytical Guide
  • For (d)(i): Multiply $I \times V \times 300$.
  • For (d)(ii): Multiply mass of water ($50\text{ g}$) $\times$ specific heat capacity ($4.2\text{ J}/(\text{g}\cdot^\circ\text{C})$) $\times \Delta\theta$. Verify that $Q_W \le Q_H$.
  • For (d)(iii): Divide $Q_W$ by $Q_H$ and round to 2 or 3 significant figures (or express as a percentage if clearly indicated with `%`).
✅ Layer 3: Full Worked Solution & Mark Scheme
  • (d)(i) Energy supplied by heater $Q_H$: $$Q_H = I \times V \times t = 1.40 \times 2.9 \times 300 = 1218\text{ J} \approx 1200\text{ J (2 s.f.)}$$ [B1]
  • (d)(ii) Energy gained by water $Q_W$: $$Q_W = 50 \times 4.2 \times \Delta\theta = 50 \times 4.2 \times 4.5 = 945\text{ J} \approx 950\text{ J (2 s.f.)}$$ Note: Mark scheme explicitly requires $Q_W \le Q_H$ for credit. Here $945\text{ J} < 1218\text{ J}$. [B1]
  • (d)(iii) Efficiency of heater: $$\text{efficiency} = \frac{Q_W}{Q_H} = \frac{945}{1218} = 0.776 \approx 0.78 \text{ (or } 78\%\text{)}$$ [B1]
🚀 Layer 4: Examiner's Extension Challenge: Notice the mark scheme condition on 1(d)(ii): and Qw ≤ QH. If a candidate fabricates a temperature rise $\Delta\theta$ that makes $Q_W > Q_H$ (violating the First Law of Thermodynamics / conservation of energy, giving an efficiency $> 100\%$), they automatically lose the mark in 1(d)(ii)!
1(e)

Suggest one change that can be made to the apparatus you have used in this investigation that will increase the efficiency of the heater. [1 mark]

💡 Layer 1: Conceptual Orientation

Efficiency is $\dfrac{Q_W}{Q_H}$. For a fixed electrical input $Q_H$, how can we reduce thermal energy escaping from the open glass beaker into the surrounding air and bench?

🔍 Layer 2: Method & Analytical Guide

Heat is lost mainly via convection/evaporation from the open water surface and conduction/radiation through the glass walls. Identify an apparatus modification that blocks these pathways.

✅ Layer 3: Full Worked Solution & Mark Scheme

Official Answer: Insulate (lag) the beaker (e.g., wrap in cotton wool/foam jacket) OR add a lid/cover to the beaker to reduce thermal energy loss to the surroundings. [B1]

Question 2: Refraction of Light Through a Transparent Block

10 Marks

Experimental Context: You investigate the refraction of a narrow ray of light from an illuminated slit passing through a rectangular transparent acrylic/glass block ($110\text{ mm} \times 70\text{ mm} \times 20\text{ mm}$) placed on line $XY$ in Fig. 2.1.

Fig. 2.1: Complete Ray Trace Construction (Parts 2a & 2b) Rectangular Block Outline [2(b)(i)] X Y Normal [2(a)(i)] M L i = 40° P r = 25° Two crosses (×) ≥ 5 cm apart [2(b)(ii)]
2(a)(i)–(ii) & 2(b)(i)–(v)

Follow the ray-tracing instructions shown in Fig. 2.1 above:
• 2(a)(i): Draw a normal to $XY$ at $M$ ($8\text{ cm}$ above and below $XY$). [1]
• 2(a)(ii): Draw incident line $LM$ at an angle of $40^\circ$ to the normal. [1]
• 2(b)(i): Place the block on $XY$ with its top-left corner at $X$ and draw its outline. [1]
• 2(b)(ii): Shine the ray along $LM$ and mark two crosses ($\times$) on the emergent ray. [1]
• 2(b)(iii): Remove the block, join the crosses to meet the lower block edge at $P$. [1]
• 2(b)(iv): Draw a straight line joining $M$ and $P$. [1]
• 2(b)(v): Measure and record the angle of refraction $r$ between $MP$ and the normal. [1]

°
💡 Layer 1: Conceptual Orientation

Why must the two crosses ($\times$) marked on the emergent ray in part 2(b)(ii) be placed far apart rather than right next to each other? Between which two lines is the angle of refraction $r$ measured?

🔍 Layer 2: Method & Analytical Guide
  • The two crosses on the emergent ray must be placed at least $5\text{ cm}$ apart so that any slight hand-marking error does not cause the extrapolated line to miss point $P$.
  • Measure $r$ between the refracted ray $MP$ inside the block and the normal (never between $MP$ and the boundary $XY$!).
  • By Snell's Law with $n \approx 1.50$: $\sin r = \dfrac{\sin 40^\circ}{1.50} = \dfrac{0.6428}{1.50} = 0.4285 \Rightarrow r = 25.4^\circ \approx 25^\circ$.
✅ Layer 3: Full Worked Solution & Mark Scheme
  • 2(a)(i): Normal drawn at $90^\circ$ to $XY$ at point $M$. [B1]
  • 2(a)(ii): Line $LM$ drawn at $40^\circ \pm 1^\circ$ to the normal and labelled $L$. [B1]
  • 2(b)(i): Rectangular block outline drawn with its top left-hand corner at $X$. [B1]
  • 2(b)(ii): Two crosses ($\times$) marked at least $5\text{ cm}$ apart below the block and to the right of $M$. [B1]
  • 2(b)(iii): Crosses joined and extended back to meet the bottom edge of the block, labelled $P$. [B1]
  • 2(b)(iv): Points $M$ and $P$ joined with a neat ruled straight line inside the block. [B1]
  • 2(b)(v): Angle of refraction recorded: $$r = 25^\circ \quad (\text{Mark scheme range: } 25^\circ \pm 2^\circ \text{ i.e. } 23^\circ \text{ to } 27^\circ)$$ [B1]
2(c)

The refractive index $n$ of the transparent block is given by the equation: $$n = \frac{\sin 40^\circ}{\sin r}$$ Calculate $n$ and give your answer to 2 significant figures. [2 marks]

💡 Layer 1: Conceptual Orientation

Ensure your calculator is in DEGREE (DEG) mode before evaluating $\sin 40^\circ$ and $\sin 25^\circ$. Does refractive index $n$ have a unit? How many digits should appear in a 2 significant figure answer?

🔍 Layer 2: Method & Analytical Guide

Evaluate the unrounded ratio first: $$\sin 40^\circ = 0.64279, \quad \sin 25^\circ = 0.42262$$ Divide the two values, then round the result to exactly 2 significant figures.

✅ Layer 3: Full Worked Solution & Mark Scheme
$$n = \frac{\sin 40^\circ}{\sin 25^\circ} = \frac{0.6428}{0.4226} = 1.521 \approx 1.5 \text{ (to 2 s.f.)}$$
  • Correct calculation of $n$ from candidate's value of $r$ (expected $n = 1.5 \pm 0.1$). [M1]
  • Final answer recorded to 2 significant figures (e.g. $1.5$, no unit). [A1]
🚀 Layer 4: Examiner's Extension Challenge: Writing $n = 1.52$ loses the second mark (`[A1]`) because the question explicitly instructs: "give your answer to 2 significant figures". Also remember that refractive index $n$ is a dimensionless ratio—do not attach a degree symbol ($^\circ$) to $n$!
2(d)

Suggest how you could change the experiment to make sure that your value of $n$ is accurate. [1 mark]

💡 Layer 1: Conceptual Orientation

In part (b), you only measured $r$ for a single angle of incidence ($i = 40^\circ$), and a wide ray of light makes it hard to judge the exact center of the beam. How can you improve reliability and accuracy?

🔍 Layer 2: Method & Analytical Guide

State either a multi-angle repetition method (varying $i$ and averaging $n$, or plotting $\sin i$ against $\sin r$) or a beam/line sharpness improvement.

✅ Layer 3: Full Worked Solution & Mark Scheme

Any one from: [B1]

  • Repeat for different angles of incidence and calculate a mean (average) value of $n$ (or plot a graph of $\sin i$ against $\sin r$ to find the gradient).
  • Use thinner pencil lines / a narrower beam of light (narrower slit) to mark the center of the ray more accurately.

Question 3: Kinematics of a Marble Rolling Down a Slope

14 Marks

Experimental Context: You first determine the average mass of one glass marble (diameter $\approx 1.5\text{ cm}$) using $5$ identical marbles and a top-pan balance. Then you release a marble from the $90.0\text{ cm}$ mark down a track made from two parallel metre rules spaced $0.8\text{ cm}$ apart (Fig. 3.1) for ramp heights $h = 4.0\text{ cm}, 6.0\text{ cm}, 8.0\text{ cm}, 10.0\text{ cm}$, and $12.0\text{ cm}$.

View from Above (Two Metre Rules with 0.8 cm Gap) 100 cm 90 cm 0 cm ↕ 0.8 cm gap Fig. 3.1: Side View of Ramp Arrangement boss & clamp height h d = 90.0 cm travel distance stopper
3(a)(i)–(ii)

(i) Place the empty dish on the top-pan balance, press zero (tare), and add the $5$ marbles. Record the mass of the $5$ marbles. [1 mark]
(ii) Calculate the average mass of $1$ marble. [1 mark]

📋 Supervisor Sample Mass Reading

Mass of 5 identical glass marbles ($1.5\text{ cm}$ diameter): $25.0\text{ g}$ (Mark scheme accepted range: $25.0\text{ g} \pm 2.0\text{ g}$, i.e., $23.0\text{ g}$ to $27.0\text{ g}$)

g
💡 Layer 1: Conceptual Orientation

Why do we weigh $5$ marbles together and divide by $5$ rather than weighing just $1$ marble on the balance?

🔍 Layer 2: Method & Analytical Guide

Measuring multiple identical items reduces the percentage uncertainty of the balance reading and averages out tiny manufacturing variations between individual glass balls. Divide total mass by $5$.

✅ Layer 3: Full Worked Solution & Mark Scheme
  • 3(a)(i): $\text{mass of 5 marbles} = 25.0\text{ g}$ (within $25.0\text{ g} \pm 2.0\text{ g}$). [B1]
  • 3(a)(ii): $$\text{average mass of 1 marble} = \frac{25.0\text{ g}}{5} = 5.0\text{ g}$$ [B1]
3(b)(i)–(ii)

(i) For initial height $h = 4.0\text{ cm}$, release the marble from the $90.0\text{ cm}$ mark and record three timings $t_1, t_2, t_3$ to hit the stopper, then calculate the mean $t_{\text{av}}$. [1 mark]
(ii) Repeat for $h = 6.0\text{ cm}, 8.0\text{ cm}, 10.0\text{ cm}$, and $12.0\text{ cm}$ and complete Table 3.1. [2 marks]

$h\text{ / cm}$ $t_1\text{ / s}$ $t_2\text{ / s}$ $t_3\text{ / s}$ $t_{\text{av}}\text{ / s}$
4.0 2.61 2.57 2.62 2.60
6.0 2.11 2.15 2.10 2.12
8.0 1.84 1.81 1.87 1.84
10.0 1.63 1.67 1.65 1.65
12.0 1.52 1.48 1.50 1.50
s
💡 Layer 1: Conceptual Orientation

How does the acceleration of a rolling sphere depend on the angle of inclination $\sin\theta = \dfrac{h}{L}$? As $h$ increases down the table, should $t_{\text{av}}$ increase or decrease?

🔍 Layer 2: Method & Analytical Guide

For a solid sphere rolling without slipping on a groove, $a = \dfrac{5}{7} g_{\text{eff}} \sin\theta \propto h$, so travel time $t = \sqrt{\dfrac{2d}{a}} \propto \dfrac{1}{\sqrt{h}}$. For each row, compute $t_{\text{av}} = \dfrac{t_1 + t_2 + t_3}{3}$ and round consistently to 2 decimal places.

✅ Layer 3: Full Worked Solution & Mark Scheme
  • 3(b)(i): Mean $t_{\text{av}}$ correctly calculated from 3 recorded timings at $h = 4.0\text{ cm}$: $$t_{\text{av}} = \frac{2.61 + 2.57 + 2.62}{3} = 2.60\text{ s}$$ [B1]
  • 3(b)(ii): All results recorded in Table 3.1 and all means correctly calculated. [B1]
  • Correct trend of $t_{\text{av}}$ decreasing down the table as $h$ increases. [B1]
3(b)(iii)–(iv) & 3(c)(i)–(ii)

3(b)(iii): Plot a graph of $t_{\text{av}}\text{ / s}$ on the y-axis against $h\text{ / cm}$ on the x-axis. Draw a line of best fit. [4 marks]
3(b)(iv): Describe the relationship between $h$ and $t_{\text{av}}$. [1 mark]
3(c)(i): Use your graph to find $t_{\text{av}}$ when $h = 7.0\text{ cm}$. Show your working on the graph. [2 marks]
3(c)(ii): Calculate the average speed $v = \dfrac{d}{t_{\text{av}}}$ of the marble when $h = 7.0\text{ cm}$ and state the unit. [2 marks]

Fig. 3.2: Graph of Average Time t_av / s against Ramp Height h / cm 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 11.0 12.0 13.0 h / cm 1.40 1.60 1.80 2.00 2.20 2.40 2.60 2.80 t_av / s Read-off at h = 7.0 cm: t_av = 1.96 s [3(c)(i)]
s
cm/s
💡 Layer 1: Conceptual Orientation

Look at Fig. 3.1 carefully: what is the exact distance $d$ that the marble travels along the track from its release point to the wooden stopper? Is it $100\text{ cm}$ or $90.0\text{ cm}$?

🔍 Layer 2: Method & Analytical Guide
  • Graphing checklist [4 marks]: Label both axes with quantity and unit ($t_{\text{av}}\text{ / s}$ and $h\text{ / cm}$); choose linear scales without awkward multiples (do not need to start at $(0,0)$); plot points accurately to within $\frac{1}{2}$ small square; draw a thin smooth best-fit line/curve.
  • Distance trap in 3(c)(ii): The marble is released at the $90.0\text{ cm}$ mark and hits the stopper at $0\text{ cm}$, so $d = 90.0\text{ cm} = 0.90\text{ m}$ (NOT $100\text{ cm}$!).
✅ Layer 3: Full Worked Solution & Mark Scheme
  • 3(b)(iii) Graph [4 marks]:
    • Axes labelled with both quantity and unit ($t_{\text{av}}\text{ / s}$ on y-axis, $h\text{ / cm}$ on x-axis). [B1]
    • Scales linear, sensible, and not awkward (occupying more than half the grid). [B1]
    • All 5 points plotted accurately to the nearest $\frac{1}{2}$ small square. [B1]
    • Thin, continuous best-fit line/curve drawn through the points. [B1]
  • 3(b)(iv) Relationship: As $h$ increases, $t_{\text{av}}$ decreases (non-linearly / at a decreasing rate). [B1]
  • 3(c)(i) Graph Interpolation:
    • Clear dashed construction/working lines drawn on the graph at $h = 7.0\text{ cm}$ up to the line and across to the $t_{\text{av}}$ axis. [M1]
    • Correct reading from graph: $t_{\text{av}} = 1.96\text{ s}$. [A1]
  • 3(c)(ii) Average Speed Calculation:
    $$v = \frac{d}{t_{\text{av}}} = \frac{90.0\text{ cm}}{1.96\text{ s}} = 45.9\text{ cm/s} \approx 46\text{ cm/s} \quad \left(\text{or } \frac{0.90\text{ m}}{1.96\text{ s}} = 0.46\text{ m/s}\right)$$
    • Correct numerical evaluation of average speed from candidate's $t_{\text{av}}$ using $d = 90\text{ cm}$ or $0.90\text{ m}$. [B1]
    • Matching unit $\text{cm/s}$ (for $46$) or $\text{m/s}$ (for $0.46$). [B1]
🚀 Layer 4: Examiner's Extension Challenge: The most common error in 3(c)(ii) is substituting $d = 100\text{ cm}$ ($1.0\text{ m}$) because students see "metre rule" and forget that the marble was released from the $90.0\text{ cm}$ mark! Always check the diagram and question stem for the actual travel distance.

Question 4: Extended Planning — Electrical Power Output of a Solar Cell

6 Marks

Planning Task: Plan an experiment to investigate how the brightness of the light falling on a solar cell affects the electrical power output ($\text{power} = \text{current} \times \text{voltage}$) of the solar cell.
Available Apparatus: Solar cell connected to a fixed resistor (incomplete circuit in Fig. 4.1), a lamp connected to a power supply, a metre rule, a voltmeter, an ammeter, and connecting leads.

Fig. 4.1: Completed Circuit Diagram & Distance Variation Arrangement (MP1 & MP2) Lamp Metre rule: vary distance d + − Solar Cell A ← Ammeter in series [MP2] Fixed Resistor V Voltmeter in parallel [MP2]
Q4 Plan

Self-Assess Your 6-Point Experimental Plan Against Official Examiner Criteria: [6 marks]

Tick each marking point you included in your written plan to calculate your score out of 6:

Your Planning Score: 0 / 6 Marks
💡 Layer 1: Conceptual Orientation

Examine the apparatus list: why did the examiners include a metre rule in an experiment about light brightness? How does changing the distance $d$ between a lamp and a solar cell change the light intensity reaching the cell?

🔍 Layer 2: Method & Analytical Guide

Structure your response using the 5 bullet prompts in the question paper: (1) Independent variable manipulation ($d$ with metre rule), (2) Circuit completion on Fig. 4.1, (3) Control variables (darkened room + constant lamp supply voltage), (4) Full results table with units, and (5) Graph of $P = IV$ vs $d$.

✅ Layer 3: Full Worked Solution & Model 6-Mark Response

1. Circuit & Apparatus Setup [MP2]:
Complete the circuit in Fig. 4.1 by connecting the ammeter in series with the solar cell and fixed resistor (across the open gap on the right), and connecting the voltmeter in parallel across the solar cell (or across the fixed resistor).

2. Method to Vary Light Brightness [MP1 & MP3]:
Place the lamp facing the solar cell and use the metre rule to measure the distance $d$ from the lamp filament to the surface of the solar cell. Start with $d = 10.0\text{ cm}$, switch on the lamp, and record the current $I$ from the ammeter and voltage $V$ from the voltmeter. Repeat the measurements for at least five different distances ($d = 20.0\text{ cm}, 30.0\text{ cm}, 40.0\text{ cm}, 50.0\text{ cm}$, and $60.0\text{ cm}$) to vary the brightness of light falling on the cell. [MP1] [MP2] [MP3]

3. Control Variables [MP4]:

  • Perform the experiment in a darkened room (keep background/ambient lighting constant).
  • Keep the voltage/power supply to the lamp constant throughout the investigation.
  • Keep the angle/alignment of the solar cell perpendicular to the light beam. [MP4]

4. Results Table [MP5]:

Distance $d\text{ / cm}$ Current $I\text{ / A}$ Voltage $V\text{ / V}$ Electrical Power $P\text{ / W}$
    
    

[MP5]

5. Reaching a Conclusion [MP6]:
For each distance $d$, calculate the electrical power output of the solar cell using $P = I \times V$. Plot a graph of electrical power $P\text{ / W}$ (y-axis) against distance $d\text{ / cm}$ (x-axis) (or compare the calculated power values in the table) to determine how light brightness affects the power output of the solar cell. [MP6]

0 comments:

Post a Comment