Cambridge O Level Physics 5054/42 May/June 2026 – Complete Interactive Worked Solutions
Interactive laboratory revision guide featuring precision vector diagrams, scale-reading simulations, 4-Layer Thinking Scaffolding, and official Cambridge mark scheme criteria (Maximum Mark: 40 • Duration: 1 Hour).
Question 1: Simple Pendulum Oscillations & Determination of $g$
10 MarksA student investigates the oscillations of a pendulum and determines two values for the acceleration due to gravity. The student arranges the pendulum in a clamp as shown in Figure 1.1. The length $l$ of the pendulum is the distance from the bottom of the clamp to the centre of the pendulum bob.
💡 Layer 1: Conceptual Orientation
Look carefully at the top and bottom dashed reference lines in Figure 1.1. The length $l$ begins at the bottom face of the clamp ($0.0\text{ cm}$ mark) and ends exactly at the centre of mass of the spherical bob. What precision does "to the nearest $0.1\text{ cm}$" require in terms of decimal places?
🔍 Layer 2: Method & Analytical Guide
Aligning the zero mark of a millimetre scale with the bottom of the clamp shows the centre of the bob coinciding exactly with the $7\text{ cm}$ graduation mark. Because a ruler graduated in millimetres has a smallest division of $0.1\text{ cm}$, you must include the trailing `.0` to show measurement to the nearest millimetre.
✅ Layer 3: Full Worked Solution & Mark Scheme
Measuring directly from the bottom of the clamp to the centre of the pendulum bob gives:
💡 Layer 1: Conceptual Orientation
If a diagram is drawn to "one-fifth ($\frac{1}{5}$) full size", is the real pendulum in the laboratory 5 times longer or 5 times shorter than the drawing? Also check the column heading in Table 1.1: what unit is required for $L$?
🔍 Layer 2: Method & Analytical Guide
1. Multiply the drawing length $l$ by $5$ to obtain the actual length in centimetres.
2. Divide by $100$ to convert centimetres into metres ($\text{m}$): $L = l \times 5 \div 100 = l \times 0.05$.
✅ Layer 3: Full Worked Solution & Mark Scheme
Mark Scheme Guidance: Error carried forward (ECF) is allowed from candidate's $\text{(a)(i)} \times 0.05$.
(b) Procedure: The student gives the bob a small sideways displacement and releases it so that it oscillates, then measures the time $t$ for $20$ oscillations of the pendulum. The stopwatch reading is shown in Figure 1.2.
| $L\ /\ \text{m}$ | $t\ /\ \text{s}$ | $T\ /\ \text{s}$ |
|---|---|---|
| 0.350 [from (a)(ii)] | 23.8 [from (b)(i)] | 1.19 [from (b)(ii)] |
| $0.700$ | $34.0$ | $1.70$ |
💡 Layer 1: Conceptual Orientation
What is the unrounded reading shown on the digital stopwatch in Figure 1.2? Notice the question asks you to record $t$ to 3 significant figures, matching the precision of $34.0\text{ s}$ in the second row.
🔍 Layer 2: Method & Analytical Guide
The stopwatch displays $0\text{ min } 23\text{ s}$ and $\frac{75}{100}\text{ s}$, which is $23.75\text{ s}$. Rounding $23.75\text{ s}$ to 3 significant figures means rounding to the nearest tenth of a second.
✅ Layer 3: Full Worked Solution & Mark Scheme
Mark Scheme Guidance: $23.8\text{ (s)}$ — correct answer only (CAO).
💡 Layer 1: Conceptual Orientation
If $20$ complete oscillations take time $t$, how do you find the time $T$ for a single oscillation?
🔍 Layer 2: Method & Analytical Guide
Use the relation $T = \frac{t}{20}$. Substitute $t = 23.8\text{ s}$ (or $23.75\text{ s}$) and round the result to 3 significant figures.
✅ Layer 3: Full Worked Solution & Mark Scheme
Note: Using unrounded $23.75 \div 20 = 1.1875\text{ s}$ also rounds to $1.19\text{ s}$ to 3 significant figures. Mark scheme requires 3 significant figures only, correctly rounded (ECF from $\text{(b)(i)} \div 20$).
Select the valid mathematical justification:
💡 Layer 1: Conceptual Orientation
What is the strict mathematical condition for two variables $T$ and $L$ to be directly proportional ($T \propto L$)? Look at how $L$ changes from $0.350\text{ m}$ to $0.700\text{ m}$.
🔍 Layer 2: Method & Analytical Guide
You can prove $T$ is not proportional to $L$ in two equivalent ways:
• Doubling test: $L$ doubles ($0.350\text{ m} \times 2 = 0.700\text{ m}$), whereas $T$ goes from $1.19\text{ s}$ to $1.70\text{ s}$ (note that $1.19 \times 2 = 2.38\text{ s} \neq 1.70\text{ s}$).
• Ratio test: Calculate $\frac{T}{L}$ (or $\frac{L}{T}$) for both rows and show they are not equal.
✅ Layer 3: Full Worked Solution & Mark Scheme
Method 1 (Doubling argument): When $L$ doubles from $0.350\text{ m}$ to $0.700\text{ m}$, the period $T$ does not double (it increases from $1.19\text{ s}$ to $1.70\text{ s}$, whereas $2 \times 1.19\text{ s} = 2.38\text{ s}$). $\mathbf{[B1]}$
Method 2 (Ratio $\frac{T}{L}$ or $\frac{L}{T}$ argument):
Since $\frac{T}{L}$ (or $\frac{L}{T}$) is not constant, $T$ is not directly proportional to $L$. $\mathbf{[B1]}$
(ii) Calculate a second value $g_2$ for the acceleration due to gravity, using the data for $L = 0.700\text{ m}$ from Table 1.1. [1]
💡 Layer 1: Conceptual Orientation
Why does the formula have the constant $39$ in the numerator? Recall that for a simple pendulum, $T = 2\pi\sqrt{\frac{L}{g}} \implies g = \frac{4\pi^2 L}{T^2}$, and $4\pi^2 \approx 39.48 \approx 39$. Be sure not to forget to square $T$ in the denominator!
🔍 Layer 2: Method & Analytical Guide
• For $g_1$: substitute $L = 0.35\text{ m}$ and $T = 1.19\text{ s}$, then round strictly to 2 significant figures.
• For $g_2$: substitute $L = 0.700\text{ m}$ and $T = 1.70\text{ s}$.
✅ Layer 3: Full Worked Solution & Mark Scheme
(d)(i) Calculation of $g_1$:
(d)(ii) Calculation of $g_2$:
Mark Scheme Guidance: For (d)(i), $g_1 = 9.6$ must be given to 2 significant figures (ECF from (a)(ii) and (b)(ii)). For (d)(ii), accept $9.4$, $9.45$, or $9.446\text{ m/s}^2$ (any significant figures $> 1$).
💡 Layer 1: Conceptual Orientation
How do you test quantitatively whether two experimental values ($g_1 = 9.6\text{ m/s}^2$ and $g_2 = 9.4\text{ m/s}^2$) lie within $10\%$ of one another? Remember you must show a numerical calculation using both values and state a clear conclusion.
🔍 Layer 2: Method & Analytical Guide
You can use any of three standard methods accepted by Cambridge examiners:
1. Percentage difference: $\frac{|g_1 - g_2|}{g_1} \times 100\%$ and compare with $10\%$.
2. $10\%$ threshold check: Calculate $10\%$ of $g_1$ ($0.96\text{ m/s}^2$) and compare it with $|g_1 - g_2| = 0.2\text{ m/s}^2$.
3. Ratio check: Compute $\frac{g_2}{g_1}$ and show that it is greater than $0.90$ ($90\%$).
✅ Layer 3: Full Worked Solution & Mark Scheme
Calculation (any one valid form): $\mathbf{[M1]}$
Statement: Yes, the two values can be considered to be the same within the limits of experimental accuracy because the difference ($2.1\%$) is less than $10\%$. $\mathbf{[A1]}$
Select an experimental accuracy technique credited by the mark scheme:
💡 Layer 1: Conceptual Orientation
Consider the two measurements made in this experiment: measuring length $L$ with a ruler and measuring time $t$ for oscillations with a stopwatch. What practical technique minimizes error in either measurement?
🔍 Layer 2: Method & Analytical Guide
Think about: (1) How the ruler is positioned and read relative to the pendulum, or (2) How the student marks the centre of oscillation and counts swings from $0$ when starting the stopwatch.
✅ Layer 3: Full Worked Solution & Mark Scheme
Any one of the following techniques earns $\mathbf{[B1]}$:
- Place the metre rule close to the pendulum when measuring the length.
- View the metre rule perpendicularly (at right angles / eye level) to avoid parallax error.
- Ensure the ruler is vertical / perpendicular to the bench (e.g. using a set square).
- Use a fiducial marker (reference pin/line) at the centre of oscillation (equilibrium position) to time passages.
- Start counting oscillations from zero ("$0, 1, 2, \dots$") when starting the stopwatch.
- Also accepted: Repeat timings and calculate an average / time a large number of oscillations.
Question 2: Comparing Methods of Reducing the Rate of Cooling
10 MarksA student compares two methods of reducing the rate of temperature decrease in a beaker of hot water. The student uses two identical beakers, P and Q. Beaker P is wrapped with a layer of insulation but has no lid. Beaker Q has a lid but no layer of insulation, as shown in Figure 2.1.
(a) Procedure: The student pours $200\text{ cm}^3$ of hot water into beaker P, places a thermometer into the water, waits until the thermometer reading has stopped increasing, records the temperature $\theta$ of the hot water, immediately starts a stopwatch, allows the hot water to cool for $240\text{ s}$, and measures the temperature in Table 2.1 at $t = 240\text{ s}$. The maximum thermometer reading at $t = 0$ is shown in Figure 2.2.
| beaker P | beaker Q | |
|---|---|---|
| $t\ /\ $ s | $\theta\ /\ $ °C | $\theta\ /\ $ °C |
| $0$ | 89 [from (a)(i)] | $90$ |
| $240$ | $77$ | $82$ |
(a)(ii) The student repeats the procedure for beaker Q. Add units to the column headings in Table 2.1. [1]
💡 Layer 1: Conceptual Orientation
Between $80^\circ\text{C}$ and $90^\circ\text{C}$ on the thermometer in Figure 2.2, there are $10$ equal intervals. How many degrees does each minor tick mark represent? Also check the procedure text for the exact units of $t$ ($240\text{ s}$) and $\theta$ ($^\circ\text{C}$).
🔍 Layer 2: Method & Analytical Guide
• Each scale division equals $\frac{90 - 80}{10} = 1^\circ\text{C}$. The top of the grey liquid column is exactly $1$ division below $90^\circ\text{C}$.
• Standard SI/Cambridge symbol for seconds is $\text{s}$ (or written out in full as $\text{seconds}$), and for degrees Celsius is $^\circ\text{C}$.
✅ Layer 3: Full Worked Solution & Mark Scheme
(a)(i): $\theta = 89\ (^\circ\text{C}) \quad \mathbf{[B1]}$ (Correct answer only).
(a)(ii): Column headings completed as: $t\ /\ \mathbf{s}$, $\theta\ /\ \mathbf{^\circ\text{C}}$, $\theta\ /\ \mathbf{^\circ\text{C}} \quad \mathbf{[B1]}$
(b)(ii) Calculate the rate of temperature decrease of the water in each beaker using: $$\text{rate of temperature decrease} = \frac{\text{temperature decrease}}{\text{time}}$$ Give your answers to $2$ significant figures in $^\circ\text{C/min}$. [2]
💡 Layer 1: Conceptual Orientation
Look closely at the printed unit on the answer line in part (b)(ii): it asks for the rate in $^\circ\text{C/min}$, whereas the cooling time in the table is given as $240\text{ s}$. How many minutes are in $240\text{ s}$?
🔍 Layer 2: Method & Analytical Guide
1. Temperature decrease: $\Delta\theta_P = 89 - 77 = 12^\circ\text{C}$ and $\Delta\theta_Q = 90 - 82 = 8^\circ\text{C}$.
2. Convert time to minutes: $t = \frac{240\text{ s}}{60\text{ s/min}} = 4.0\text{ min}$.
3. Divide each temperature decrease by $4.0\text{ min}$ and express both answers to 2 significant figures ($3.0$ and $2.0$).
✅ Layer 3: Full Worked Solution & Mark Scheme
(b)(i) Temperature decreases:
(b)(ii) Rate of temperature decrease (with $t = 240\text{ s} = 4.0\text{ min}$):
Award $\mathbf{[B1]}$ for both numerical values correct ($3$ and $2$), and $\mathbf{[B1]}$ for both answers expressed to 2 significant figures ($3.0$ and $2.0$).
(c) State two factors that must be controlled to make a valid comparison between the rates of temperature decrease of beaker P and beaker Q. [2]
(d) A student wants to find how the rate of decrease of temperature of the water in a beaker surrounded by a layer of insulation compares with the rate of decrease of temperature of the water in a beaker with no insulation. Suggest one change to the apparatus that will enable this new comparison to be made. [1]
(e) Handling a beaker containing hot water is dangerous. State one safety precaution that the student takes when doing the experiment. [1]
Self-Check Quiz on Parts (b)(iii) – (e):
💡 Layer 1: Conceptual Orientation
• In (b)(iii), does a "more effective insulator" produce a higher or lower rate of cooling?
• In (d), originally P has (Insulation, No Lid) and Q has (No Insulation, Lid). If you want the only difference between P and Q to be the layer of insulation, what must you do about the lid?
🔍 Layer 2: Method & Analytical Guide
• (b)(iii): Compare $2.0\text{ }^\circ\text{C/min}$ (Q) with $3.0\text{ }^\circ\text{C/min}$ (P).
• (c): Identify environmental and apparatus variables that affect cooling rate (volume of water, initial temperature, room temperature, beaker dimensions).
• (d): Either remove the lid from Q (so both have no lid) or add an identical lid to P (so both have a lid).
• (e): Name a concrete piece of personal protective equipment or handling tool for hot liquids.
✅ Layer 3: Full Worked Solution & Mark Scheme
(b)(iii) Conclusion: Beaker Q, because the rate of cooling is less ($2.0\text{ }^\circ\text{C/min} < 3.0\text{ }^\circ\text{C/min}$) / it has a smaller temperature decrease ($8^\circ\text{C} < 12^\circ\text{C}$) in the same time. $\mathbf{[B1]}$
(c) Two Control Variables (any two for $\mathbf{[B2]}$):
- Volume (or mass / amount) of hot water.
- Initial (starting) temperature of the hot water.
- Room (ambient) temperature / draughts.
- Time of cooling ($240\text{ s}$).
- Size / shape / thickness / material of the beaker.
(d) Apparatus Modification: Remove the lid from beaker Q OR add an identical lid to beaker P (and repeat the experiment). $\mathbf{[B1]}$
(e) Safety Precaution: Wear heat-resistant gloves (when handling the beaker) / use tongs to hold the hot beaker / wear safety goggles. $\mathbf{[B1]}$
Examiner Note: Simply writing "do not touch the beaker" or "be careful" is ignored as too vague.
Question 3: Potential Difference Across Resistors & Internal Resistance
14 MarksA student investigates the potential difference across resistors in a circuit. The student assembles the circuit shown in Figure 3.1, connects a $12\ \Omega$ resistor into the gap between terminals P and Q, connects a voltmeter to measure the potential difference across the resistor, closes the switch, and measures the potential difference $V$ and current $I$.
(a)(ii) On Figure 3.1, using the correct circuit symbol, draw a voltmeter connected to measure the potential difference across the resistor. [1]
💡 Layer 1: Conceptual Orientation
What is the standard IEC/Cambridge circuit symbol for a fixed resistor? Does the horizontal wire line pass through the rectangle, or stop at its ends? How must a voltmeter always be connected relative to the component whose potential difference it measures?
🔍 Layer 2: Method & Analytical Guide
• Draw an empty rectangular box between P and Q with connecting leads meeting the left and right sides (do not draw a line straight through the middle of the rectangle).
• Draw a circle containing a capital letter $\text{V}$ connected in a parallel branch across the resistor (with junctions outside the resistor symbol).
✅ Layer 3: Full Worked Solution & Mark Scheme
See the blue and green additions in Figure 3.1 above:
- (a)(i): Rectangular resistor symbol connected between P and Q, with no line drawn through the symbol. $\mathbf{[B1]}$
- (a)(ii): Circle with letter $\text{V}$ inside (no line through the circle) connected in parallel with the resistor between P and Q. $\mathbf{[B1]}$
(b) The voltmeter and ammeter readings for the $12\ \Omega$ resistor are shown in Figure 3.2.
| resistance $R\ /\ \Omega$ | potential difference $V\ /\ \text{V}$ | current $I\ /\ \text{A}$ |
|---|---|---|
| $12$ | 3.9 [from (b)(i)] | 0.33 [from (b)(ii)] |
| $15$ | $4.0$ | $0.27$ |
| $18$ | $4.1$ | $0.23$ |
| $22$ | $4.2$ | $0.19$ |
| $33$ | $4.3$ | $0.13$ |
(b)(ii) Record, in Table 3.1, the current $I$ in the circuit with the $12\ \Omega$ resistor. [1]
💡 Layer 1: Conceptual Orientation
Determine the value of $1$ smallest division on each analog scale:
• On the voltmeter, there are $10$ divisions between $3\text{ V}$ and $4\text{ V}$.
• On the ammeter, there are $50$ divisions between $0\text{ A}$ and $0.5\text{ A}$ (with longer marks every $10$ divisions at $0.1, 0.2, 0.3, 0.4\text{ A}$). You can also cross-check using Ohm's Law: $I = \frac{V}{R} = \frac{3.9\text{ V}}{12\ \Omega}$!
🔍 Layer 2: Method & Analytical Guide
• Voltmeter: $1\text{ division} = 0.1\text{ V}$. Pointer is at $4.0 - 0.1 = 3.9\text{ V}$.
• Ammeter: $1\text{ division} = 0.01\text{ A}$. Pointer is $3$ divisions past $0.30\text{ A}$, reading $0.33\text{ A}$ (consistent with $\frac{3.9\text{ V}}{12\ \Omega} = 0.325\text{ A} \approx 0.33\text{ A}$).
✅ Layer 3: Full Worked Solution & Mark Scheme
(b)(i): $V = 3.9\text{ (V)} \quad \mathbf{[B1]}$ (Correct answer only; mark scheme explicitly notes: "not accept 3.90" because the rest of the column is recorded to 1 d.p. and the scale division is $0.1\text{ V}$).
(b)(ii): $I = 0.33\text{ (A)} \quad \mathbf{[B1]}$ (Correct answer only).
(d) Determine the gradient $G$ of your line. Show all working, and indicate on the graph the values you use. [2]
(e) The magnitude of gradient $G$ of your line is equal to the resistance $r$ of the battery. Write down the value of $r$ to the nearest ohm. [2]
💡 Layer 1: Conceptual Orientation
Why does the terminal potential difference $V$ decrease linearly as current $I$ increases? By Kirchhoff's loop rule for a battery of e.m.f. $E$ and internal resistance $r$: $$V = E - Ir$$ Comparing with $y = c + mx$, plotting $V$ against $I$ yields a straight line with y-intercept $E$ and slope $-r$!
🔍 Layer 2: Method & Analytical Guide
4 Graph Plotting Marks in 3(c):
1. Axes labelled with quantity and unit ($V\ /\ \text{V}$ on y-axis, $I\ /\ \text{A}$ on x-axis).
2. Linear, non-awkward scales starting at $I = 0\text{ A}$ on the x-axis and a non-zero value (e.g. $3.8\text{ V}$) on the y-axis so plotted points cover at least half the grid.
3. All 5 points plotted accurately to within $\pm \frac{1}{2}$ small square using neat crosses ($\times$).
4. Thin, single best-fit straight line drawn through the trend of all points.
Gradient Marks in 3(d) & 3(e): Choose two points on the line separated by at least half the plotted span ($\Delta V \ge 0.2\text{ V}$) and show the triangle or coordinates on the graph.
✅ Layer 3: Full Worked Solution & Mark Scheme
(c) Graph Mark Allocation: Axes labelled $\mathbf{[B1]}$, sensible linear scales filling $\ge \frac{1}{2}$ grid $\mathbf{[B1]}$, 5 accurate plots $\mathbf{[B1]}$, thin straight line of best fit $\mathbf{[B1]}$.
(d) Gradient Calculation: Using triangle points $(0.08\text{ A}, 4.40\text{ V})$ and $(0.33\text{ A}, 3.90\text{ V})$ indicated on the graph $\mathbf{[B1]}$, spanning $\Delta V = 0.50\text{ V} \ge 0.2\text{ V}$ $\mathbf{[B1]}$:
(e) Internal Resistance $r$:
- Value of $G$ within range $(-)1.8\ \Omega$ to $(-)2.2\ \Omega$ inclusive $\mathbf{[B1]}$.
- $r = G$ recorded to the nearest ohm: $r = 2\ \Omega$ $\mathbf{[B1]}$.
(g) When doing the experiment, it is important that the terminals P and Q are not allowed to come into contact with each other at any time. Suggest why terminals P and Q must not touch. [1]
Select the pair of statements that satisfies the mark scheme for (f) and (g):
💡 Layer 1: Conceptual Orientation
• In (f), the e.m.f. $E$ is the potential difference across the battery when no current is drawn ($I = 0$). Where should the student connect the voltmeter probes?
• In (g), if P and Q touch with no resistor between them, what is the external resistance $R$? What happens to the current $I = \frac{E}{r}$ and the thermal energy dissipated in the wires, battery, and ammeter?
🔍 Layer 2: Method & Analytical Guide
• For (f), specify connecting the voltmeter in parallel across the battery terminals.
• For (g), note that the mark scheme ignores the bare phrase "causes a short circuit" unless you state the physical consequence: a very large current flows, wires/battery get hot, insulation melts, or the ammeter/cells are damaged.
✅ Layer 3: Full Worked Solution & Mark Scheme
(f): Connect the voltmeter in parallel with the battery terminals (when the switch is open / on open circuit). $\mathbf{[B1]}$
(g): Any one of the following specific consequences $\mathbf{[B1]}$:
- A (very) high / large current flows.
- The cells / battery are damaged (or battery heats up / drains rapidly).
- The wires get (very) hot / insulation melts / circuit overheats.
- The ammeter is damaged.
Question 4: Experiment Planning – Fan Speed & Rate of Cooling
6 MarksWhen air moves over the surface of hot water in a beaker, it changes the rate of cooling of the hot water. Plan an experiment to investigate the relationship between the speed of a fan producing the moving air and the rate of cooling of the hot water in the beaker.
The apparatus available includes: a supply of hot water, a beaker, a thermometer, and an electric fan with five speed settings. You may also use any apparatus commonly available in a school laboratory.
In your plan include:
- any other apparatus needed
- a brief description of the method, including what you will measure and how you make sure that your measurements are accurate
- the variables you will control
- a results table to record your measurements (you are not required to enter any readings in the table)
- how you will process your results to reach a conclusion.
Interactive Examiner's 6-Point Rubric Checklist (Tick each marking point to verify your plan):
💡 Layer 1: Conceptual Orientation
Look at the apparatus list given in the question: hot water, beaker, thermometer, and 5-speed electric fan. What essential piece of measuring apparatus is missing if you need to measure a rate of cooling ($\frac{\Delta\theta}{t}$)?
🔍 Layer 2: Method & Analytical Guide
Structure your 6-mark response using clear subheadings matching the bullet points in the prompt: Additional Apparatus, Method & Accuracy, Control Variables, Results Table, and Processing & Conclusion. Remember that control variables must be stated explicitly, and every measured physical quantity in your table header must have a unit.
✅ Layer 3: Model Full-Mark Plan & Official Marking Points (MP1–MP6)
1. Additional Apparatus Needed $\mathbf{[MP1]}$:
- A stopwatch (to measure the cooling time) and a measuring cylinder (to measure a fixed volume of hot water) and a metre rule (to keep the distance between the fan and beaker constant).
2. Method & Accuracy Precautions $\mathbf{[MP2, MP3]}$:
- Place the beaker on the bench at a fixed distance (e.g. $30.0\text{ cm}$ measured with a metre rule) in front of the electric fan, and set the fan to speed setting $1$.
- Use the measuring cylinder to pour $200\text{ cm}^3$ of hot water into the beaker. Stir gently, wait for the thermometer reading to reach a steady maximum, and record the initial temperature $\theta_{\text{initial}}$ (viewing the thermometer scale perpendicularly at eye level to avoid parallax error). $\mathbf{[MP2]}$
- Immediately start the stopwatch and switch on the fan. Allow the water to cool for a fixed time $t = 240\text{ s}$ (or $4.0\text{ min}$), stir gently, and record the final temperature $\theta_{\text{final}}$. $\mathbf{[MP2]}$
- Empty the beaker, refill with $200\text{ cm}^3$ of hot water at the same starting temperature, and repeat the experiment for each of the other fan speed settings ($2, 3, 4$, and $5$). Repeat at each setting and take an average to improve reliability. $\mathbf{[MP3]}$
3. Control Variables (State explicitly — any one scores $\mathbf{[MP4]}$):
- Initial temperature of the hot water at $t = 0$.
- Volume / mass of hot water used in each trial.
- Distance between the electric fan and the beaker.
- Room temperature and using the same beaker (same material, surface area, and thickness).
4. Results Table $\mathbf{[MP5]}$:
| Fan speed setting | Initial temperature $\theta_{\text{initial}}\ /\ ^\circ\text{C}$ | Final temperature $\theta_{\text{final}}\ /\ ^\circ\text{C}$ | Time $t\ /\ \text{s}$ | Temperature decrease $\Delta\theta\ /\ ^\circ\text{C}$ | Rate of cooling $R\ /\ (^\circ\text{C/s})$ |
|---|---|---|---|---|---|
| 1 | |||||
| 2 | |||||
| 3 | |||||
| 4 | |||||
| 5 |
5. Data Processing & Conclusion $\mathbf{[MP6]}$:
- For each fan speed setting, calculate the temperature decrease $\Delta\theta = \theta_{\text{initial}} - \theta_{\text{final}}$ and the rate of cooling $R = \frac{\Delta\theta}{t}$.
- Plot a graph (or bar chart) of rate of cooling against fan speed setting (or plot temperature against time for each fan speed, or compare the values in the table to see if/how the fan speed affects the rate of cooling).
0 comments:
Post a Comment