Sunday, 22 November 2026

Cambridge IGCSE Physics 0625/63 May/June 2026 Worked Solutions (Paper 6 Alternative to Practical)

Cambridge IGCSE™ Physics 0625/63 Paper 6 Alternative to Practical May/June 2026 • 1 Hour • 40 Marks

Cambridge IGCSE Physics 0625/63 (May/June 2026) — Complete Interactive Worked Solutions

Step-by-step worked solutions with clean exam apparatus diagrams, interactive tables, plotted graphs, official Cambridge mark codes, and 4-layer thinking scaffolding.

Mastery Tracker: 0 / 22 checks  •  Estimated Marks: 0 / 40
Question Core Practical Topic Key ATP Skills Tested Marks
Q1 Density of identical coins (2 methods) Significant figures, meniscus reading, full-size scale measurement, 10% accuracy test 11
Q2 Spring extension vs. suspended mass Extension arrow, parallax avoidance, graph plotting & best-fit line, $L = l_0 + e$, safety 11
Q3 Resistors connected in parallel Ammeter & voltmeter wiring, analogue scale ($0.05\text{ A}$/div), inverse proportionality, anomalies 11
Q4 Rate of temperature rise of heated water 7-mark experimental plan: variable, apparatus, method, controls, blank table, analysis 7

Question 1 — Measuring the Density of Identical Coins

Total: 11 marks

A student has five identical coins. The student measures the density of one of these coins by two different methods.

Method 1: Electronic Balance & Water Displacement
1(a)(i) [1 mark]

The student measures the mass $m_1$ of one coin. The reading on the balance is shown in Figure 1.1. Record the mass of the coin to two significant figures.

8.89 g Figure 1.1
g
💡 Layer 1: Conceptual Orientation

Count significant figures starting from the first non-zero digit on the left. Look at the third digit on the display: should it round the tenths digit up or leave it unchanged?

🔍 Layer 2: Method & Analytical Guide

The raw display shows $8.89\text{ g}$ (3 significant figures). Because the third digit is $9 \ge 5$, round the second significant figure up from $8$ to $9$.

✅ Layer 3: Full Worked Solution & Mark Scheme

Balance reading $= 8.89\text{ g}$. Rounding to 2 significant figures:

$m_1 = \mathbf{8.9}\text{ g}$ [B1]
🚀 Layer 4: Examiner's Extension Challenge

Examiner Trap: Writing $8.89\text{ g}$ or $8.8\text{ g}$ scores 0/1. Whenever Cambridge bolds a rounding command, the mark is awarded strictly for correct rounding.

1(a)(ii) [1 mark]

The student slowly lowers the five coins into a measuring cylinder until they are completely covered with water. Figure 1.2 shows the initial volume of water; Figure 1.3 shows the final reading after the coins have been lowered in. Record the initial and final readings.

cm³ 20 18 16 14 12 10 8 6 4 2 Figure 1.2 cm³ 20 18 16 14 12 10 8 6 4 2 Figure 1.3
cm³
cm³
💡 Layer 1: Conceptual Orientation

Determine the least count first: numbered graduations increase by $2\text{ cm}^3$ with one unlabelled tick halfway between each pair. What volume does each small tick represent?

🔍 Layer 2: Method & Analytical Guide

Each small division $= 1\text{ cm}^3$. Read the bottom of the meniscus: in Figure 1.2 it sits halfway between $10$ and $12$; in Figure 1.3 it sits halfway between $16$ and $18$.

✅ Layer 3: Full Worked Solution & Mark Scheme
Initial reading $= \mathbf{11}\text{ cm}^3$
Final reading $= \mathbf{17}\text{ cm}^3$ [B1 for both]
🚀 Layer 4: Examiner's Extension Challenge

Why submerge five coins slowly? Measuring five coins together reduces percentage uncertainty in volume by a factor of $5$. Lowering them slowly prevents water splashing out and avoids trapping air bubbles under the coins.

1(a)(iii) [1 mark]

Calculate the volume $V_1$ of one coin using your values from 1(a)(ii) and the equation:

$$V_1 = \frac{\text{final reading} - \text{initial reading}}{5}$$
cm³
💡 Layer 1: Conceptual Orientation

The water-level rise equals the total volume of all five coins. Dividing by $5$ yields the average volume of one coin.

🔍 Layer 2: Method & Analytical Guide

Total displaced volume $= 17 - 11 = 6\text{ cm}^3$. Divide $6\text{ cm}^3$ by $5$.

✅ Layer 3: Full Worked Solution & Mark Scheme
$$V_1 = \frac{17 - 11}{5} = \frac{6}{5} = 1.2\text{ cm}^3$$
$V_1 = \mathbf{1.2}\text{ cm}^3$ [B1]
🚀 Layer 4: Examiner's Extension Challenge

Error Carried Forward (ECF): Always write out your substitution step so examiners can award ECF credit even if a previous reading was slightly off.

1(a)(iv) [1 mark]

Describe one technique for measuring the volume of water in the measuring cylinder to ensure an accurate reading.

Which statement earns the mark in a Cambridge Paper 6 mark scheme?

💡 Layer 1: Conceptual Orientation

Think about how eye position affects apparent scale alignment (parallax error) and which part of the curved water surface is calibrated on glass measuring cylinders.

🔍 Layer 2: Method & Analytical Guide

Keep your line of sight perpendicular to the scale at eye level, read from the bottom of the concave meniscus, and rest the cylinder on a flat horizontal bench.

✅ Layer 3: Full Worked Solution & Mark Scheme
Eye level (perpendicular) Parallax error Bottom of meniscus

Any one of the following earns full credit:

  • View the scale perpendicularly / at eye level to avoid parallax error. [B1]
  • Read from the bottom of the meniscus. [B1]
  • Place the measuring cylinder on a flat, horizontal surface. [B1]
🚀 Layer 4: Examiner's Extension Challenge

Examiner Trap: Writing only "avoid parallax error" without stating how ("view perpendicularly / at eye level") often loses the mark. Always state the physical action.

1(a)(v) [2 marks]

Calculate the density $\rho_1$ of one coin using your values from 1(a)(i) and 1(a)(iii) and the equation $\rho_1 = \dfrac{m_1}{V_1}$. Include the unit.

💡 Layer 1: Conceptual Orientation

Your mass is in $\text{g}$ and volume is in $\text{cm}^3$, so dividing directly gives density in $\text{g/cm}^3$ without any unit conversion needed.

🔍 Layer 2: Method & Analytical Guide

Substitute $m_1 = 8.9\text{ g}$ and $V_1 = 1.2\text{ cm}^3$ into $\rho_1 = m_1 / V_1$ and round to 2 or 3 significant figures.

✅ Layer 3: Full Worked Solution & Mark Scheme
$$\rho_1 = \frac{m_1}{V_1} = \frac{8.9\text{ g}}{1.2\text{ cm}^3} = 7.4166\dots \approx 7.4\text{ g/cm}^3$$
$\rho_1 = \mathbf{7.4}$ (or $7.42$) [B1]  |  Unit: $\mathbf{\text{g/cm}^3}$ [B1]
🚀 Layer 4: Examiner's Extension Challenge

Sanity Check: Coin alloys (steel, brass, cupronickel) have densities around $7.0\text{–}8.9\text{ g/cm}^3$, confirming that $7.4\text{ g/cm}^3$ is physically realistic.

Method 2: Stack Height & Cylindrical Volume
1(b)(i) [1 mark]

The student makes a stack of the five coins, drawn full size in Figure 1.4, and records the mass $m_5 = 43.6\text{ g}$. Measure the height $h_5$ of the five coins in Figure 1.4.

h5 0 1 cm Figure 1.4 (Full size on A4 paper; screen ruler matched to scale)
cm
💡 Layer 1: Conceptual Orientation

Trace horizontally from the top edge of the fifth coin across to the millimetre ruler on the right. How many millimetres above $1.0\text{ cm}$ does it align with?

🔍 Layer 2: Method & Analytical Guide

On the true-to-scale A4 PDF, each coin measures $0.28\text{ cm}$ thick, so five coins stacked flush measure $5 \times 0.28\text{ cm} = 1.40\text{ cm}$.

✅ Layer 3: Full Worked Solution & Mark Scheme
$h_5 = \mathbf{1.4}\text{ cm}$ (Cambridge tolerance: $1.3\text{ cm}$ to $1.5\text{ cm}$) [B1]
🚀 Layer 4: Examiner's Extension Challenge

Printing Tip: Always print past papers at 100% Actual Size so full-size diagrams are not shrunk by "Fit to Page".

1(b)(ii) [1 mark]

The radius $r$ of each coin is $1.2\text{ cm}$. Calculate the volume $V_5$ of the five coins using your value from 1(b)(i) and the equation:

$$V_5 = \pi \times r^2 \times h_5$$
cm³
💡 Layer 1: Conceptual Orientation

The stack is modelled as a cylinder of radius $r = 1.2\text{ cm}$ and height $h_5 = 1.4\text{ cm}$. Remember to square only $r$.

🔍 Layer 2: Method & Analytical Guide

Compute $r^2 = (1.2)^2 = 1.44\text{ cm}^2$, then multiply by $\pi$ and by $1.4\text{ cm}$.

✅ Layer 3: Full Worked Solution & Mark Scheme
$$V_5 = \pi \times (1.2)^2 \times 1.4 = 6.333\dots\text{ cm}^3$$
$V_5 = \mathbf{6.3}\text{ cm}^3$ (or $6.33\text{ cm}^3$) [B1]
🚀 Layer 4: Examiner's Extension Challenge

Keep the full unrounded calculator display ($6.333\dots$) in memory for part 1(b)(iii) to avoid rounding drift.

1(b)(iii) [1 mark]

Calculate another value $\rho_2$ for the density of one coin using the values from 1(b) ($m_5 = 43.6\text{ g}$) and the equation $\rho_2 = \dfrac{m_5}{V_5}$.

g/cm³
💡 Layer 1: Conceptual Orientation

Both $m_5$ and $V_5$ belong to the same five identical coins, so dividing them directly gives the density of the coin material without dividing by $5$ again.

🔍 Layer 2: Method & Analytical Guide

Substitute $m_5 = 43.6\text{ g}$ and $V_5 = 6.333\text{ cm}^3$ into $\rho_2 = m_5 / V_5$.

✅ Layer 3: Full Worked Solution & Mark Scheme
$$\rho_2 = \frac{43.6}{6.333} = 6.884\dots \approx 6.9\text{ g/cm}^3$$
$\rho_2 = \mathbf{6.9}\text{ g/cm}^3$ (or $6.88\text{ g/cm}^3$) [B1]
🚀 Layer 4: Examiner's Extension Challenge

Examiner Trap: Never divide $\rho_2$ by $5$ at the end. Density is an intensive property: one coin and five identical coins have the exact same density.

1(c) [2 marks]

Two quantities can be considered equal within the limits of experimental accuracy if their values are within $10\%$ of each other. State whether $\rho_1$ from Method 1 and $\rho_2$ from Method 2 can be considered equal. Support your statement with a calculation.

Compare $\rho_1 = 7.4\text{ g/cm}^3$ and $\rho_2 = 6.9\text{ g/cm}^3$:

💡 Layer 1: Conceptual Orientation

Do not judge by eye. Compute the percentage difference between $\rho_1$ and $\rho_2$, then compare your result directly against the $10\%$ limit.

🔍 Layer 2: Method & Analytical Guide

Step 1: Find the difference $|\rho_1 - \rho_2| = 7.4 - 6.9 = 0.5\text{ g/cm}^3$.

Step 2: Divide by $\rho_1$ (or $\rho_2$) and multiply by $100\%$ to get the percentage difference.

✅ Layer 3: Full Worked Solution & Mark Scheme
$$\text{Percentage difference} = \frac{7.4 - 6.9}{7.4} \times 100\% = 6.8\%$$

Note: Dividing by $6.9$ instead gives $7.2\%$, which is also less than $10\%$.

Calculation: $6.8\% < 10\%$ [M1]
Statement: Yes, $\rho_1$ and $\rho_2$ can be considered equal within the limits of experimental accuracy because their percentage difference is less than $10\%$. [A1]
🚀 Layer 4: Examiner's Extension Challenge

Why is $\rho_2$ slightly lower than $\rho_1$? Embossed coin surfaces trap tiny air gaps between stacked coins, slightly overestimating $h_5$ and $V_5$ and pulling $\rho_2$ slightly below $\rho_1$.

Question 2 — Hooke's Law: Spring Extension & Graphical Analysis

Total: 11 marks

A student investigates the relationship between the extension $e$ of a spring and the mass $m$ suspended from the spring using masses of $10\text{ g}, 20\text{ g}, 30\text{ g}, 40\text{ g},$ and $50\text{ g}$.

2(a)(i) [1 mark]

Figure 2.1 shows the arrangement of the apparatus. On Figure 2.1, draw a double-headed arrow (↕) to show the extension of the spring when mass $m$ is suspended from the spring.

clamp spring l0 clamp spring mass m L Figure 2.1

Where must the double-headed arrow for extension $e$ start and end?

💡 Layer 1: Conceptual Orientation

Extension is the increase in length, $e = L - l_0$. Since both springs start at the same clamp height, compare the positions of their lower ends.

🔍 Layer 2: Method & Analytical Guide

Project a horizontal dashed line from the bottom end of $l_0$ across to the stretched spring. Draw a vertical double-headed arrow between that level and the bottom end of $L$.

✅ Layer 3: Full Worked Solution & Mark Scheme
Top of spring coils (fixed level) l0 L extension e = L − l₀
Vertical double-headed arrow spanning from the bottom level of $l_0$ to the bottom level of $L$. [B1]
🚀 Layer 4: Examiner's Extension Challenge

Examiner Trap: Match the exact endpoints used by the exam paper's own $l_0$ and $L$ arrows (the ends of the coiled section); do not extend your arrow down to the mass hanger.

2(a)(ii) [2 marks]

Describe two techniques the student uses to measure accurately the length of the spring.

Which pair of techniques earns full 2/2 marks?

💡 Layer 1: Conceptual Orientation

Consider how to prevent parallax error, ruler tilt, and oscillation errors when measuring a vertically suspended spring.

🔍 Layer 2: Method & Analytical Guide

State two concrete physical methods: eye-level perpendicular reading, a set square or horizontal pointer, clamping the ruler vertically close to the spring, or waiting for oscillations to stop.

✅ Layer 3: Full Worked Solution & Mark Scheme

Any two distinct techniques [B1] + [B1]:

  • View the ruler scale perpendicularly / at eye level to avoid parallax error.
  • Use a set square or horizontal pointer against the ruler to align the ends of the spring with the scale.
  • Clamp the ruler vertically and place it as close as possible to the spring.
  • Wait until the spring and mass have stopped oscillating before reading.
🚀 Layer 4: Examiner's Extension Challenge

Examiner Trap: Vague statements such as "measure carefully" or "avoid human error" receive 0 marks.

2(b)(i) [1 mark]

Calculate the extension $e$ when a mass of $40\text{ g}$ is suspended from the spring using $e = L - l_0$, and enter your value in Table 2.1.

Table 2.1 (Interactive Entry)
mass $m$ / g length $L$ / cm extension $e$ / cm
01.90.0
102.40.5
202.80.9
303.31.4
40 3.7
504.22.3
💡 Layer 1: Conceptual Orientation

Read the original unstretched length $l_0$ from the $m = 0\text{ g}$ row of Table 2.1, then subtract it from $L$ at $m = 40\text{ g}$.

🔍 Layer 2: Method & Analytical Guide

From row 1, $l_0 = 1.9\text{ cm}$. At $m = 40\text{ g}$, $L = 3.7\text{ cm}$. Compute $3.7 - 1.9$.

✅ Layer 3: Full Worked Solution & Mark Scheme
$$e = L - l_0 = 3.7 - 1.9 = 1.8\text{ cm}$$
Table 2.1 entry at $m = 40\text{ g}$: $e = \mathbf{1.8}\text{ cm}$ [B1]
🚀 Layer 4: Examiner's Extension Challenge

Checking successive differences ($0.0 \to 0.5 \to 0.9 \to 1.4 \to 1.8 \to 2.3$) confirms a steady rise of $0.4\text{–}0.5\text{ cm}$ per $10\text{ g}$.

2(b)(ii) [3 marks]

Plot a graph of extension $e/\text{cm}$ ($y$-axis) against mass $m/\text{g}$ ($x$-axis). Start the axes from the origin $(0,0)$ and draw a best-fit straight line.

0 0 m / g e / cm

Which plotting method earns all 3 Cambridge graph marks?

💡 Layer 1: Conceptual Orientation

Cambridge graph marks reward three distinct habits: sensible linear scales covering at least half of each axis, accurate plotting to within half a small square, and a single thin best-fit line.

🔍 Layer 2: Method & Analytical Guide
  • $x$-axis scale: $0$ to $50\text{ g}$ using $10\text{ g}$ per major square ($1\text{ small div} = 2\text{ g}$).
  • $y$-axis scale: $0$ to $2.5\text{ cm}$ using $0.5\text{ cm}$ per major square ($1\text{ small div} = 0.1\text{ cm}$).
  • Points to plot: $(0,0.0), (10,0.5), (20,0.9), (30,1.4), (40,1.8), (50,2.3)$.
✅ Layer 3: Full Plotted Graph & Mark Scheme
0 10 20 30 40 50 m / g 0 0.5 1.0 1.5 2.0 2.5 e / cm m = 12 g e = 0.55 cm
  • Suitable linear scales from $(0,0)$ filling ≥50% of both axes [B1]
  • All 6 points plotted accurately to within $\pm \frac{1}{2}$ small square [B1]
  • Thin, well-balanced straight line of best fit drawn with a ruler [B1]
🚀 Layer 4: Examiner's Extension Challenge

Use a sharp HB pencil and small neat crosses (×). Thick blobs or double-drawn lines immediately lose the best-fit line mark.

2(b)(iii) [3 marks]

Use your graph to determine the length $L$ of the spring when a mass of $12\text{ g}$ is suspended from the spring. Show clearly on the graph how you obtained the necessary information.

cm
💡 Layer 1: Conceptual Orientation

The $y$-axis of your graph reads extension $e$, but the question asks for total length $L$. What must you add to $e$ after reading the graph?

🔍 Layer 2: Method & Analytical Guide

Step 1: Draw a vertical dashed line from $m = 12\text{ g}$ up to the best-fit line, then horizontally to the $y$-axis to read $e \approx 0.55\text{ cm}$.

Step 2: Add the original unstretched length $l_0 = 1.9\text{ cm}$ using $L = l_0 + e$.

✅ Layer 3: Full Worked Solution & Mark Scheme
$$e = 0.55\text{ cm} \implies L = l_0 + e = 1.9 + 0.55 = 2.45\text{ cm}$$
Construction lines clearly shown on graph at $m = 12\text{ g}$ [B1]
Extension read from best-fit line: $e = 0.55\text{ cm}$ (accept $0.5\text{–}0.6\text{ cm}$) [B1]
$L = \mathbf{2.45}\text{ cm}$ (or $\mathbf{2.5}\text{ cm}$) [B1]
🚀 Layer 4: Examiner's Extension Challenge

Classic 3-Mark Trap: Writing $L = 0.55\text{ cm}$ stops one step too early. Always check whether the answer line asks for extension $e$ or total length $L$.

2(c) [1 mark]

Suggest one safety precaution the student takes when doing the experiment.

Select the specific safety precaution for a spring-and-masses experiment:

💡 Layer 1: Conceptual Orientation

Focus on the two real physical hazards: a stretched spring snapping toward your eyes, or slotted masses dropping onto your feet.

🔍 Layer 2: Method & Analytical Guide

State one concrete protective action: safety goggles, a cushioned mat under the masses, or clamping the retort stand to the bench.

✅ Layer 3: Full Worked Solution & Mark Scheme

Any one valid precaution [B1]:

  • Wear safety goggles / eye protection in case the spring snaps.
  • Place a cushion / soft mat underneath the masses (or keep feet out of the way).
  • Clamp the retort stand securely to the bench with a G-clamp or counterweight.
🚀 Layer 4: Examiner's Extension Challenge

Generic lab rules ("tie hair back", "do not run") never earn credit in Paper 6; link your precaution directly to the apparatus.

Question 3 — Electric Circuit with Combinations of Parallel Resistors

Total: 11 marks

A student investigates an electric circuit containing different combinations of identical resistors connected in parallel.

3(a) [2 marks]

On Figure 3.1, complete the circuit to show a voltmeter connected to measure the potential difference (p.d.) across the resistor, and an ammeter connected to measure the current in the circuit.

+ − Figure 3.1

How should the ammeter and voltmeter be connected?

💡 Layer 1: Conceptual Orientation

Current flows through an ammeter (connected in series), whereas potential difference is measured across a component by a voltmeter (connected in parallel).

🔍 Layer 2: Method & Analytical Guide

Draw a circle with A closing the right-hand gap. Add a parallel branch across the resistor containing a circle with V.

✅ Layer 3: Full Worked Solution, Completed Circuit & Mark Scheme
+ − A V Completed Circuit: Ammeter (series) & Voltmeter (parallel)
Voltmeter symbol (V) connected in parallel across the resistor [B1]
Ammeter symbol (A) connected in series in the right-hand gap [B1]
🚀 Layer 4: Examiner's Extension Challenge

Never draw a connecting wire straight through the meter circle, and ensure all junctions meet cleanly without breaks.

3(b) [1 mark]

The student measures the p.d. $V$ across the resistor and the current $I$ in the circuit. Record, in Table 3.1, the value of $I$ shown on the ammeter in Figure 3.2.

0 0.5 1 1.5 A Figure 3.2
A
💡 Layer 1: Conceptual Orientation

Count the number of small intervals between $0$ and $0.5\text{ A}$ to find the value of one small division before reading the pointer.

🔍 Layer 2: Method & Analytical Guide

There are $10$ small divisions between $0$ and $0.5\text{ A}$, so each small division $= 0.05\text{ A}$. The pointer sits on the 6th tick after $0$.

✅ Layer 3: Full Worked Solution & Mark Scheme
$$I = 6 \times 0.05\text{ A} = 0.30\text{ A}$$
$I = \mathbf{0.30}\text{ A}$ (or $0.3\text{ A}$) [B1]
🚀 Layer 4: Examiner's Extension Challenge

Recording $0.30$ matches the 2-decimal-place precision of the other readings in Table 3.1 ($0.60, 0.85, 1.15, 1.45$).

3(c)(i) & 3(c)(ii) [1 + 1 marks]

(i) Complete the column headings in Table 3.1. (ii) Calculate the resistance $R$ when there is one resistor in the circuit using $R = \dfrac{V}{I}$.

Table 3.1 (Interactive Headings & Calculation)
number of resistors $V$ / $I$ / $R$ /
1 0.75 0.30
20.750.601.25
30.750.850.88
40.751.150.65
50.751.450.52
💡 Layer 1: Conceptual Orientation

Recall the SI unit symbols for potential difference, current, and resistance, then compute $R = V/I$ for row 1.

🔍 Layer 2: Method & Analytical Guide

Complete the headings as $V / \text{V}$, $I / \text{A}$, and $R / \Omega$ (you can type ohm or Ω), then divide $0.75$ by $0.30$.

✅ Layer 3: Full Worked Solution & Mark Scheme
$$R = \frac{V}{I} = \frac{0.75}{0.30} = 2.50\ \Omega$$
3(c)(i) Column headings: $V / \mathbf{V}$,   $I / \mathbf{A}$,   $R / \mathbf{\Omega}$ [B1]
3(c)(ii) Resistance for 1 resistor: $R = \mathbf{2.50}\ \Omega$ (or $2.5\ \Omega$) [B1]
🚀 Layer 4: Examiner's Extension Challenge

Recording $2.50$ keeps every entry in the $R$ column consistent to 2 decimal places.

3(c)(iii) [2 marks]

Describe the relationship between the number of resistors in the circuit and the resistance $R$ in the circuit. Justify your answer using values from Table 3.1.

Which response earns both marks?

💡 Layer 1: Conceptual Orientation

For $N$ identical resistors in parallel, $R = R_1 / N$. To prove inverse proportionality from Table 3.1, test whether the product $N \times R$ remains approximately constant.

🔍 Layer 2: Method & Analytical Guide
$N$12345
$R$ / $\Omega$2.501.250.880.650.52
$N \times R$ / $\Omega$2.502.502.642.602.60

When $N$ doubles from $1$ to $2$, $R$ halves from $2.50\ \Omega$ to $1.25\ \Omega$, and $N \times R$ stays close to $2.55\ \Omega$ across all five rows.

✅ Layer 3: Full Worked Solution & Mark Scheme
Relationship: Resistance $R$ is inversely proportional to the number of resistors $N$ in parallel. [B1]
Justification: Doubling $N$ from $1$ to $2$ halves $R$ from $2.50\ \Omega$ to $1.25\ \Omega$, and the product $N \times R$ stays constant at $2.5\text{–}2.6\ \Omega$ within experimental accuracy. [B1]
🚀 Layer 4: Examiner's Extension Challenge

Notice that $N \times R$ rises slightly from $2.50$ to $2.64$ as total current increases — a direct clue to the heating effect discussed in 3(c)(iv).

3(c)(iv) [2 marks]

The resistors heat up during the investigation and this affects the values for the resistance $R$. Suggest two improvements to reduce this heating effect.

Which pair of improvements directly reduces electrical heating?

💡 Layer 1: Conceptual Orientation

Heating energy is $E = I^2Rt = (V^2/R)t$. Reduce either the time $t$ current flows, the supply voltage $V$, or the current $I$.

🔍 Layer 2: Method & Analytical Guide

Pair one procedural improvement (switching off between readings) with one circuit improvement (lower supply e.m.f., series protective resistor, or higher-value resistors).

✅ Layer 3: Full Worked Solution & Mark Scheme

Any two distinct improvements [B1] + [B1]:

  • Switch off / open the switch between readings so current flows only briefly.
  • Use a lower supply voltage to reduce current.
  • Add a fixed or variable resistor in series with the power supply to limit current.
  • Use resistors of higher resistance.
🚀 Layer 4: Examiner's Extension Challenge

Always state how to reduce current (e.g., lower supply voltage or add a series resistor) rather than writing "use a smaller current" alone.

3(d) [2 marks]

The student takes repeat readings. Table 3.2 shows the ammeter readings for three resistors in parallel: 0.85, 0.58, 0.90, 0.80. Identify the anomalous reading and suggest one reason for this anomaly.

A
💡 Layer 1: Conceptual Orientation

Three readings cluster tightly around $0.80\text{–}0.90\text{ A}$. Which value sits far outside that group, and what circuit fault or reading mistake could produce it?

🔍 Layer 2: Method & Analytical Guide

$0.58\text{ A}$ is almost identical to the 2-resistor current ($0.60\text{ A}$) in Table 3.1, pointing to a loose connection on one resistor, or digit transposition ($0.85 \to 0.58$).

✅ Layer 3: Full Worked Solution & Mark Scheme
Anomalous reading: $\mathbf{0.58}\text{ A}$ [B1]
Reason (any one): One resistor had a loose/poor connection; or the student misread the ammeter scale / transposed the digits; or the resistors overheated. [B1]
🚀 Layer 4: Examiner's Extension Challenge

When calculating a mean from repeat readings, always exclude the anomaly: $(0.85 + 0.90 + 0.80) / 3 = 0.85\text{ A}$.

Question 4 — Experimental Planning: Rate of Heating Water

Total: 7 marks

A student investigates the rate at which the temperature of water inside a beaker increases when the water is heated. Plan an experiment to investigate how one variable affects the rate at which the temperature of the water increases.

Apparatus available: a selection of beakers, an electrical water heater, and a supply of water. In your plan: state the one variable investigated; name any other apparatus needed; describe the method and measurements; state key control variables; draw a table with column headings (no readings entered); and explain how to use the readings to reach a conclusion.

beaker of water power supply electrical water heater stirrer thermometer stopwatch

If you choose volume of water as your independent variable, which apparatus and control set is complete for full marks?

💡 Layer 1: Conceptual Orientation

Rate of temperature increase is $\dfrac{\theta_2 - \theta_1}{t}$, so you must measure both temperature change and time, and repeat across at least 5 values of your chosen independent variable.

🔍 Layer 2: Method & Analytical Guide

Vary the volume of water across 5 values ($100, 150, 200, 250, 300\text{ cm}^3$), keep the beaker, heater power, starting temperature, and heating time ($180\text{ s}$) constant, and plot rate of temperature rise against volume.

✅ Layer 3: Full 7-Mark Model Plan & Mark Scheme

1. Independent variable: Volume (or mass) of water in the beaker. [B1]

2. Additional apparatus: Thermometer, stopwatch / stopclock, measuring cylinder (or top-pan balance), and stirrer. [B1]

3. Method & measurements: [B2]

  • Measure $100\text{ cm}^3$ of water with the measuring cylinder and pour it into a beaker.
  • Record the initial temperature $\theta_1$ with the thermometer (bulb clear of the beaker base).
  • Immerse the electrical heater fully, switch it on, and start the stopwatch simultaneously.
  • After a fixed time $t = 180\text{ s}$, stir the water gently and record the final temperature $\theta_2$.
  • Repeat for at least four other volumes ($150, 200, 250, 300\text{ cm}^3$), letting the heater cool between trials.

4. Key control variables: Same heater and power supply voltage; same initial temperature $\theta_1$; same beaker (material & diameter) and room temperature; same heating time $t$. [B1]

5. Results table (headings with units, no data): [B1]

Volume $V$ / cm³ Initial temp. $\theta_1$ / °C Final temp. $\theta_2$ / °C Temp. rise $\Delta\theta$ / °C Time $t$ / s Rate / °C s−1
      
      

6. Reaching a conclusion: Calculate $\text{rate} = \dfrac{\theta_2 - \theta_1}{t}$ for each volume and plot a graph of rate ($y$-axis) against volume of water ($x$-axis) to see how volume affects the heating rate. [B1]

🚀 Layer 4: Examiner's Extension Challenge — Alternative Full-Mark Variables

You can equally earn 7/7 by investigating the diameter / surface area of the beaker (extra apparatus: ruler, thermometer, stopwatch, measuring cylinder) or beaker material / insulation (keeping water volume constant).

Final Revision Checklist — Top 6 Cambridge Paper 6 Habits

  1. Bold Rounding Commands: Always honour bolded instructions such as two significant figures (Q1(a)(i)) and match existing table decimal places (Q3(b), Q3(c)(ii)).
  2. Least Count First: Divide the gap between two numbered marks by the number of small divisions before reading any scale (Q1(a)(ii): $1\text{ cm}^3$; Q3(b): $0.05\text{ A}$).
  3. Extension vs. Total Length: Re-read the symbol on the answer line ($e$ vs. $L$) after reading off a Hooke's law graph (Q2(b)(iii)).
  4. Numerical 10% Justification: Always show a percentage difference calculation before stating two results are equal within experimental limits (Q1(c)).
  5. Inverse Proportionality Proof: Check $N \times R \approx \text{constant}$ or a doubling/halving pair from the table (Q3(c)(iii)).
  6. 7-Mark Plan Structure: Address all 6 prompt bullets with bold headings, at least 5 trials, and units in every table header (Q4).

0 comments:

Post a Comment